Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
It will explain the features and operation of your unit and help insure trouble free installation. FEATURES • Class ''D'' Technology • 1 Ohm Stable • Spec Audiophile Grade Components • High Efficiency PWM Power Supply - Multi-stranded power toroid - Tow toroidal core - MOSFET transistors • Oversized Capacitor Banks • Discrete Mount Power and speaker terminals • Variable Low Pass Electronic Crossover 50Hz -250Hz • Built in power bridging module • Circuit / Thermal / Overload Protection • Bridge Sync Capable • Remote Level Control IMPORTANT PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION ! The quality of installation may affect the performance and reliability of your product. If you have any doubts or questions regarding installation, you may wish to contact your authorized dealer. Remember to heed all wire and fuse requirements suggested in this manual. Warranty may be void if proper installation technique is not used (refer to warranty section in the rear of the manual ) 1 INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface. If you want to mount the amplifier to MDF or wood panel, drill four 3.0m/m diameter holes into mounting surface. 4. If possible, test the system to ensure it is operating correctly before final mounting of 5.Mount the amplifier using the supplied 4 self tapping screws. the amplifier. INSTALLATION DIAGRAM Self Tapping Screws FIG.1 2 FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike other amplifiers, the Class "D" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are used strictly for convenience and are paralleled internally on the amplifier. This means that if both outputs are used with one driver each, the amplifier sees the same load as if the same drivers are connected to 4OHM SUBWOOFER 4OHM SUBWOOFER 4OHM SUBWOOFER 3 4OHM SUBWOOFER only one output terminal. See diagram below. SPEAKER WIRING In both diagrams, the amplifier sees a 2 ohm load. FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ FUSE 30A 30A 30A SPEAKER G1-2000digital mono block AMPLIFIER POWER REM GNDB+ The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike other amplifiers, the Class "D" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are used strictly for convenience and are paralleled internally on the amplifier. This means that if both outputs are used with one driver each, the amplifier sees the same load as if the same drivers are connected to 4OHM SUBWOOFER 4OHM SUBWOOFER 4OHM SUBWOOFER 3 4OHM SUBWOOFER only one output terminal. See diagram below. SPEAKER WIRING In both diagrams, the amplifier sees a 2 ohm load. LINE INPUT CH1 CH2 GAIN LPF 6V 0.2V 50Hz 250Hz BASS BOOST SLAVEMASTER MASTER /SLAVE REMOTE GAIN CONTROL LINE INPUT CH1 CH2 GAIN LPF 6V 0.2V 50Hz 250Hz 0dB 12dB BASS BOOST SLAVEMASTER MASTER /SLAVE REMOTE GAIN CONTROL 4 FROM RADIO MONO BRIDGED WIRING SUBWOOFERS (DUAL AMPS) When using dual amplifiers to power one subwoofer, the Positive terminal of the Subwoofers voice coil is connected the positive terminal of the MASTER Amplifier and the Negative terminal of the Subwoofers voice coil is connected to Positive terminal on the SLAVE Amplifier. This procedure will allow the total power of both amplifiers to be added together and act like a single powerful amplifier. Please check that your subwoofer power handling capabilities are not exceeded CAUTION Always check your speaker load with a multi-meter before hooking up to the amplifier. These digital amplifiers are only 1 ohm stable. Any Impedance (load) smaller than 1 ohm will damage the amplifier. Such Damage is not covered under warranty either, so pay strict attention to what when hooking two amplifiers to it. connections are made to the amplifier. Master Amplifier Slave Amplifier MASTER SLAVE MASTER SLAVE SPEAKER WIRING 0dB 12dB LINE INPUT CH1 CH2 GAIN LPF 6V 0.2V 50Hz 250Hz BASS BOOST SLAVEMASTER MASTER /SLAVE REMOTE GAIN CONTROL LINE INPUT CH1 CH2 GAIN LPF 6V 0.2V 50Hz 250Hz 0dB 12dB BASS BOOST SLAVEMASTER MASTER /SLAVE REMOTE GAIN CONTROL 4 FROM RADIO MONO BRIDGED WIRING SUBWOOFERS (DUAL AMPS) When using dual amplifiers to power one subwoofer, the Positive terminal of the Subwoofers voice coil is connected the positive terminal of the MASTER Amplifier and the Negative terminal of the Subwoofers voice coil is connected to Positiv...
Эта инструкция также подходит к моделям:Автоусилители - G1-2000 (398.91 kb)
Автоусилители - G1-3000 (398.91 kb)