Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Pacific Accessory Corporation - Santa Ana, CA 92705 866-931-8021 • 06-29-10 TATO JBL Amplifier Turn-On Interface for Toyota CANbus Vehicles The TATO is designed to control the power and audio levels of the factory installed JBL amplifier allowing the OEM radio to be removed and replaced with an aftermarket stereo. Installation: Note: BEFORE REMOVING THE FACTORY RADIO: BALANCE AND FADE IT TO THE CENTER, TURN THE RADIO UP TO AT LEAST 3/4 VOLUME, TURN THE RADIO OFF, TURN THE IGNITION OFF & THEN PROCEED WITH REMOVING THE FACTORY RADIO Disconnect the factory radio from the OEM wiring harness and remove it from the vehicle. Make the following connections of the TATO wiring harness to the aftermarket radio: Connections: Yellow Wire - Connect to 12 Volt Constant Power on aftermarket radio• Red Wire - Connect to Accessory on aftermarket radio• Black Wire - Connect to Ground on aftermarket radio• Orange/White Wire - Connect to Dimmer on aftermarket radio• *11 Pin Harness - Connect to PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 (Sold Separately) • Red Bullet Connector - Connect to Accessory Black Bullet Connector - Connect to Ground Connect the 4 RCA connectors to the RCA outputs of the aftermarket radio • Front Left - White RCA Front Right - Grey RCA Rear Left - Green RCA Rear Right - Purple RCA If connecting the TATO to a head unit with only 2 Channel RCA outputs, use two pairs of RCA splitters (1M-2F) to split the signal. Failure to connect all 4 inputs of the TATO will result in loss of audio performance. Fade audio controls will only function with a 4 channel aftermarket deck. Connections to the TATO Interface: Connect 24-pin translucent connector • to the side of the TATO. Connect 8-pin DIN cable to the plug on • the side of the TATO. Connections to the Vehicle: Plug the main 20-pin Toyota harness into the matching factory wir• ing harness. *• If using PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2, Plug the smaller 20-pin harness into the matching factory wiring harness. Program PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2 for version #8 and follow the programming instructions included with PAC’s SWI-X, SWI-JACK, SWI-PS or SWI-ECL2. Adjusting Volume Output: When initially connecting the TATO to the vehicle the max output might not meet that of the factory radio. If the volume is low you can adjust the output using the dip switches on the side of the module. It is recommended to use a 4 volt RMS capable aftermarket radio. When adjusting the gain output it is recommended to start with the plus 7dB setting and working your way down. The dB gain adjustments are as follows: Note: It may take up to 10 seconds before the gain adjustment is heard. Set all other dip switches 4-8 to OFF (up) position Warranty: One Year Limited Warranty The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized Pacific Accessory Corporation dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspection by Pacific Accessory Corporation authorized personnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not apply to installation expenses. Attempting to service or modify this unit, operating this unit under conditions other than the recommended voltage will render this WARRANTY VOID. Unless otherwise prescribed by law, Pacific Accessory Corporation shall not be liable for any personal injury, property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse, improper installation or alteration of this product. All parts of this Pacific Accessory Corporation product are guaranteed for a period of 1 year as follows: Within the first 12 months from date of purchase, subject to the conditions above, Pacific Accessory Corporation will repair or replace the product at their discretion, if it is defective in material or workmanship providing it is returned to an Authorized Pacific Accessory Corporation Dealer, with PROOF OF PURCHASE from an authorized Pacific Accessory Corporation dealer. Warning: This equipment may be reset by unintentional electrostatic discharge during operation. Exposure to direct sunlight or extreme heat may cause damage or malfunction. FCC Class B Radio Frequency Interference Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipme...