Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Connect the small end of the power supply into the POWER 9V AC jack on the back of the answerer. Plug the other end into an AC power outlet. The unit plays a long beep and announces “please wait.” After the pause, the unit beeps again and is ready for setup or to answer calls with the default greeting and settings. CAUTION: Only use the ATLINKS USA, Inc. 5-2515 power supply that was packed with this unit. Using other power supplies may damage the unit. IMPORTANT INSTRUCTIONS FOR MOVING THE ANSWERER: To move the answerer to a different location in the house, follow these instructions: 1. Disconnect the phone line or any phones you may have connected to the unit. 2. Install a battery, if you have not already done so. This will ensure that your messages are not lost. See “Installing the Battery.” 3. Go to the electrical outlet and unplug the power supply. 4.Move the unit and phone line to the desired location. 5. Plug in the power supply into an electrical outlet. 6. Connect all necessary phone lines. SETUP RECORDING THE GREETING Before using your new answerer, you should record a greeting (the announcement callers hear when your answering system answers a call). If you don't record a greeting, callers hear a default greeting which says, "Record message after tone." When recording the greeting you should be about 6 inches from the unit. Eliminate as much background noise as possible. 1. Prepare your greeting. Sample Greeting: Hi, this is (use your name here). I can’t answer the phone right now, so please leave your name, number, and a brief message after the tone, and I’ll get back to you. Thanks. 2. Hold down the GREETING button. After the tone, you have 30 seconds to record your greeting. 3.Release the GREETING button when you finish. The greeting will playback automatically. NOTE: Your recording time should not be less than 2 seconds. Otherwise the unit will return to the default greeting. CHANGING THE SETTINGS This function allows you to change the Time/Day, Rings to Answer, and Security Code settings. SETTING THE TIME/DAY This setting allows you to set the current day and time for the Time/Day stamp attached to each message. DAY 1. Press and hold the STOP/SET button for two seconds, then release. The unit announces, “Time (the current time setting) To set day, press next...press set to continue.” 2. To change the day, press and release the NEXT or PREVIOUS button until the desired setting is announced. 3. To store the day, press and release the STOP/SET button. The unit confirms the setting and enters the Hour menu. HOUR 1. The unit announces, “ (the current hour setting) To set hour, press next...press set to continue.” 2. To change the hour, press and release the NEXT or PREVIOUS button until the desired setting is announced. 3. To store the hours, press and release the STOP/SET button. The unit confirms the setting and enters the Minute menu. MINUTES 1. The unit announces, “ (the current minutes setting) To set minutes, press next...press set to continue.” 2. To change the minutes, press and release the NEXT or PREVIOUS button until the desired setting is announced. 3. To store the minutes, press and release the STOP/SET button. The unit confirms the setting and enters the Rings to Answer menu. SETTING THE RINGS TO ANSWER This setting allows you to select the number of rings before the unit answers a call. 1. The unit announces, “Rings to Answer ( the current rings to answer setting ) To set rings, press next...press set to continue.” 2. To change the rings to answer, press and release the NEXT or PREVIOUS button until the desired setting is announced. 3. To store the Rings to Answer setting, press and release the STOP/SET button. The unit confirms the setting and enters security code menu. TOLL SAVER Toll Saver can save you the cost of making a call when you access your messages from another phone: • If you have new messages, the unit answers after the 2nd ring. • If you have no new messages, the unit answers after the 5th ring. You can hang up after the 3rd ring and save the pay telephone or long distance charge. SETTING THE SECURITY CODE This setting allows you to change the factory default security code used to access your answerer from a remote location. The default code is 123. 1. The unit announces, “Security code (the current security code) To set security code, press next...press set to continue.” 2. To change the first security code number, press and release the NEXT or PREVIOUS buttons until the desired setting is announced. The unit announces all three numbers, but only the first number will change. 3. To store the first number, press and release the STOP/SET button. A short tone will be heard. 4. To change the second and third numbers, repeat steps 2 and 3. After the third number is stored, the unit announces all the stored settings. REVIEWING THE SETTINGS This function allows you to review the current time, rings to answer, and security code. • Press and release the STOP/SET button to sta...