Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Dispose of batteries in a safe manner. Consult your local waste disposal company for disposal information. Do not burn or puncture. Like other batteries of this type, if burned it could explode and if punctured it could release corrosive material which could injure the skin or eyes and which may be toxic. Replace the Handset Battery Pack 1 Install the handset battery. b) Place the battery pack in the handset. Align the metal contacts on the battery with the contacts in the battery compartment. c) Replace cover by sliding it on its track up over battery case until it snaps firmly into place. a) Remove battery compartment cover by pressing on indentation and sliding downward. 2 Charge the handset battery. • Place the handset in the base (or a remote charging stand, purchased separately) • Charge the battery at least 12 hours. After the first charge, the battery will quick charge in only eight hours. BATTERIES Power Fail Operation You can use your cordless phone during a power outage when a fully charged battery is installed in the base unit (see “Spare Battery”). This battery will provide enough power for you to make and receive calls for up to five hours. NOTE: When using the spare battery backup power, audio quality may be somewhat reduced. Spare Battery This phone is equipped with a built-in spare battery charger in the base unit. The spare battery charger allows you to always have a charged battery available should the handset battery charge become low. NOTE: Do not switch the battery while on a call. 1 Open the spare battery compartment drawer by sliding the latch located on the side of the base unit. 2 Place the battery pack (Replacement Battery 2401, SKU# 91077, purchased separately) in the drawer, with the charge contacts facing up and to the left. 3 Push the drawer closed. 4 The spare battery takes 24 hours to fully charge. IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. For Customer Service, visit our website at or call 1 800 222–3111. Please retain your receipt as your proof of purchase. If the phone does not work at all, check these items first: • Make sure the power cord is plugged into the base and an electrical outlet not controlled by a wall switch. • Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack. • Make sure the battery pack is installed correctly. • If the screen displays LOW BATTERY, place the handset in the base and charge for at least eight hours. • If the battery does not charge after eight hours, replace it with Replacement Battery 2401, SKU# 91077. If the above suggestions do not solve the problem, try re-initializing the handset and base (see “To re-initialize the handset and base” below). If you have no dial tone: Check all the previous suggestions. If you still do not hear a dial tone, disconnect the phone and try another phone in the same jack. If there is no dial tone on that phone either, the problem is probably in your wiring or local service. If you hear a two-beep signal when you try to use the handset: • The handset and base are not communicating properly. You might be out of range. Move closer to the base and try again. • If moving closer to the base does not help, follow the directions below to re-initialize the handset and base. To re-initialize the handset and base: 1 Disconnect the power to the base. 2 Remove the handset battery pack. 3 Wait at least 15 seconds. 4 Insert the handset battery pack. 5 Connect the power to the base. 6 Put the handset in the base to re-initialize. 7 Wait for handset to display FOUND BASE. IN CASE OF DIFFICULTY If you hear noise or interference when using the phone: • You may be out of range. Move closer to the base. • Household appliances plugged into the same circuit as the base can sometimes cause interference. Try moving the appliance or the base to another outlet. • The layout of your home or office may be limiting the operating range. Try moving the base to another location, preferably on an upper floor. If the phone does not ring when you receive a call: • Make sure the Ringer is on. • Make sure the telephone line cord is connected firmly to the base and the telephone jack. • Make sure the AC adapter is plugged firmly into an electrical outlet not controlled by a wall switch. • You might be too far from the base; move closer. • You might have too many extension phones on your telephone line to allow all of them to ring. Try unplugging some of them. If your telephone misdials: • If you have dial pulse (rotary) service, you’ll need to set the Dial Mode switch to PULSE. Follow the instructions in the INSTALLATION section of this manual. • If you have touch tone service and you hear clicks while you are dialing, you’ll need to set the Dial Mode to TONE. Follow the instructions in the INSTALLATION section of this manual. If the caller’s name or phone number is not displayed: • Make sure you subscribe to a Caller ID service fro...