Оценок - , средний балл:
(
)
)
Производитель: AT&T
Размер: 411.62 kb
Название файла: 10c9d528-965c-4ee0-b250-81bc5ab044d9.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
1 2 3 4 5 6 7 8 9 * 0 # 1854 THIS NUMBER PQRS ABC DEF MNO WXYZ JKL TUV OPER GHI PROGRAM REPEAT STOP FEATURE RECORD ANNC DELETE CLOCK PLAY LOWER (AUTO) REDIAL VOLUME SPEAKER ON/OFF FWD SELECT FLASH MUTE HOLD TONE CALL LIST NEW CALL DISPLAY DIAL REMOVE LOW BATTERY Part 2 © 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico. 848229415 Issue 1AT&T INSTALLATION Remove the Base Install the Batteries Press in on tabs. Lift base off the phone. Open battery compartment door Install 4 AA batteries 5 Connect the power cord. ! Use only the power cord supplied with your system. If you need a replacement cord, call 1 800 722 9125. Fit the power cord behind the strain relief tab. Then, plug the smaller end of the power cord into the POWER jack at the back of the system. Plug the power cord into an electrical outlet not controlled by a wall switch. 6 Wait for the system to initialize. When the system is connected to AC power, all the indicator lights flash on and off. The Message Window counts down from eight to zero. After the system reaches zero, you can complete installation by following instructions in "Setting the Clock." SET UP SYSTEM 1 Install the batteries. • Turn the unit upside down. • Push in on the two tabs at the large end of the base, and lift the base off the phone. • Press the battery compartment's tab, and swing open the battery compartment door. • Insert four AA batteries. Always use four new batteries. • Close the battery compartment door. NOTE: When battery power is low, the LOW BATTERY light is on. Replace the batteries promptly to prevent the possibility of memory loss. 2 Set the Dial Mode switch. Set the switch to TT (touch tone) or DP (dial pulse) telephone service, depend ing on your telephone service. TABLE/DESK INSTALLATION 1 Attach the base. Turn the base so that the larger end is toward the top of the telephone. Reattach the base by inserting the tabs into the slots. Push down on the large end of the base to lock the base into place. 2 Connect the line cord to the telephone. Plug one end of the cord into the jack labeled TEL LINE on the bottom of the phone. Place the line cord in the channel on the base. 3 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset, then hang up. 4 Connect the line cord to a modular jack. INSTALLATION Dial Mode Switch TEL LINE jack Modular Jack Standard AC Outlet Reset Button Telephone Line Cord Power Cord WALL INSTALLATION 1 Wrap the line cord. Wrap the line cord around the posts on the inside of the base. Leave at least 3 inches free at each end of the line cord. 2 Attach the base. Turn the base so that the larger end of the base is toward the bottom of the telephone. Attach the base by inserting the tabs into the slots. Push down on the large end of the base to lock it into place. 3 Connect the line cord to the telephone. Plug one end of the line cord into the jack labeled TEL LINE on the bottom of the phone. 4 Reverse the handset tab. Hold down the switchhook, and slide the tab up and out of its slot. Turn the tab so that the end with the hook is up. Then insert the tab back into its slot. 5 Connect the line cord to modular jack and mount the phone on the wall jack. Plug the free end of the line cord into a modular wall jack. Make sure the cord snaps firmly into place. Place the phone on the wall jack mounting studs and pull down until it is securely held. 6 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the cord into the handset, then hang up. 7 Connect the power cord. ! Use only the power cord supplied with your system. If you need a replacement cord, call 1 800 722-9125. 8 Wait for the system to initialize. When the system is connected to AC power, all the indicator lights flash on and off. The Message Window counts down from eight to zero. After the system reaches zero, you can complete installation by following instructions in "Setting the Clock." SETTING THE CLOCK 1 Press C. The time is displayed. 2 Use the keypad to enter the time. 3 Press * for AM or # for PM. 4 Press C. The date is displayed. 5 Use the keypad to enter the date (for example, press 7 0 7 for July 7). 6 Press C. The year is displayed. 7 Use the keypad to enter the year. 8 Press C. The system announces the date and time. SELECTABLE DIAL INFORMATION This telephone has a push button dial which will work with tone or dial pulse (rotary) service. Even when set to dial pulse service, the phone can be switched temporarily to tone, for access to services that require tone signaling, including some tone-activated computer systems. 1854 FEATURE ANNC CLOCK ON/OFF SELECT CALL LIST NEW CALL DISPLAY DIAL REMOVE LOW BATTERY * 1 2 3 4 5 6 7 8 9 0 # THIS NUMBER PQRS ABC DEF MNO WXYZ JKL TUV OPER GHI PROGRAM LOWER (AUTO) REDIAL VOLUME SPEAKER FLASH MUTE HOLD TONE number called. Adjust speaker...