Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
O NOTE O The USOC number of thejackto beinstalledis RJ11C (or RJ11W for a wall plate jack). Attached Phone Line Cord Wall Jack DC 9V Jack Modular Phone Line Cord AC Power Cord TEL LINE Jack Attached Phone Line Cord Wall Jack DC 9V Jack Modular Phone Line Cord AC Power Cord TEL LINE Jack Preparation 7 Preparation Preparation O NOTE O Hold down SKIP/ TIME SET/CHECK continuously for Steps 1–4. TURNING THE SYSTEM ON/ OFF To turn on the system, press ON/OFF/ STOP. The display lights and the system sounds a tone. The system is set to answer calls. To turn it off, press ON/OFF/STOP.The display turns off and the system sounds 2 tones. ADJUSTING THE VOLUME Push down or pull up VOLUME ../ • to increase or decrease the volume. The system sounds a tone when you change the volume. SETTING THE DAY AND TIME The day/time voice stamp automatically defaults to Monday, 12:00 AM when you connect the system to power. 1. Turn on the system. Hold down SKIP/TIME SET/CHECK. The system sounds a tone after 1 second. 2. While holding down SKIP/TIME SET/CHECK,press REPEAT/ANNC/ DAY. The system announces “Monday” and 01 appears on the display. Repeatedly press REPEAT/ ANNC/DAY until you hear or see the correct day. 3. While holding down SKIP/TIME SET/CHECK, press MEMO/2 WAY/ HOUR. The system announces “1 AM”. 01 appears on the display. Repeatedly press MEMO/2 WAY/ HOUR until you hear or see the correct hour. 4. While holding down SKIP/TIME SET/CHECK, press PLAY/PAUSE/ MIN. The system announces “01”. 01 appears on the display. Repeatedly press or hold down PLAY/PAUSE/MIN until you hear or see the correct minute. 5. Release SKIP/TIME SET/CHECK. The system announces the day and time you set. 6. To hear the current day and time, press SKIP/TIME SET/CHECK while the system is on or off. SETTING THE NUMBER OF RINGS To control the duration before the system answers a call, slide RING SELECT on the system’s right side to the desired number of rings (2, 4, 7 or TS). TS (Toll Saver) – If you choose the Toll Saver option, and there are new O NOTES O • When you hold down PLAY/ PAUSE/MIN,the system will move forward by 10 minutes until it reaches 00. • If you have not set the day and time and you press SKIP/TIME SET/ CHECK,the system announces “Please set time”. Preparation 9 Preparation Preparation messages, the system answers after two rings. Otherwise, the system answers after four rings. This lets you avoid unnecessary charges when calling by long distance to check your messages. If you hear more than two rings, you know you can hang up because the system has no new messages. SETTING THE INCOMING MESSAGE LENGTH Slide INCOMING MSG to 1 or 5MIN (minutes) to choose the length of incoming messages. If you slide INCOMING MSG to ANN ONLY (Announcement Only), the system plays your outgoing message, but the caller cannot record a message. After the system answers, it monitors the line for 10 seconds for any remote code entry. RECORDING THE OUTGOING MESSAGE The system has a prerecorded outgoing message (OGM) that says “Hello, please leave a message after the tone.” You can use this message or record your own. 1. Hold down REPEAT/ANNC/DAY. A1 flashes on the display, and the system sounds a tone. 2. Speak your message clearly into the microphone from about 10 inches away from the system. 3. Release REPEAT/ANNC/DAY when you finish your message. The system sounds a tone and automatically plays back your recorded message. A1 appears on the display during playback. OPERATION SETTING THE SYSTEM TO ANSWER CALLS To set the system to answer calls, press ON/OFF/STOP to turn on the system. The display lights. When the system answers a call, it plays the outgoing message, then sounds a tone and begins recording. The caller can leave a 1-to 5-minute long message, depending on which option you have chosen for incoming messages (see “Setting the Incoming Message Length” on Page 10). After the caller hangs up or is silent for more O NOTES O • The maximum length for an outgoing message is about 30 seconds. When it reaches the maximum outgoing message length, the system sounds a tone and plays back the message. • If you record your own message and subsequently decide to use the prerecorded message, press REPEAT/ANNC/ DAY to play the message you recorded. While it is playing, press DELETE to erase your message. • To hear the outgoing message at any time, press REPEAT/ANNC/ DAY.To stopthe outgoing message before it ends, press ON/OFF/ STOP. Operation 11 Operation Operation than 7 seconds, or the maximum message length is reached, the system hangs up and resets to answer the next call. The number flashes to indicate a new incoming message has been recorded. When the system is answering a call or recording a message, if any phone on thesamelineis picked up or the system detects a Calling Party Control (CPC) signal, it stops playing the outgoing message or recording an incoming message and resets to answer another call. Many local phone companies use Calling Party Control (CPC) ...