Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
RVs and boats often experience severe shocks, while driving over potholes and rough road surfaces or while navigating in choppy seas. RVs and boats also experience constant vibration, from surface friction, drive engines and on-board generators. The RV1012UL and RV2012UL are engineered specifically to meet the challenges of demanding RV and marine environments—and are UL-tested to perform reliably under the most extreme shock and vibration conditions. The new RV1012UL and RV2012UL include all the features and functions of previous versions of the RV1012UL and RV2012UL listed in the enclosed owner's manual, with the following exceptions: • Ten-Point Mounting Flanges—provide up to 10 connecting points for tight adhesion to the mounting surface • Splash/Condensation Drip Shield—Added protection for control panel against potentially disruptive moisture in marine environments (required for marine applications) • Battery Recharge Rate LED Meter—indicates approximate recharge rate of connected RV or marine batteries • UL 458 (Shock/Vibration) Tested*—performs reliably in the most demanding RV and marine environments under the most extreme shock and vibration conditions (caused by potholes, rough roads, high seas, surface friction or engine/generator vibration) * Tested for conformity to UL458 and UL458 Marine Supplement—for both RV and marine applications. PowerVerter® RV1012UL & RV2012UL RV & Marine DC-to-AC Inverter/Chargers 1111 W. 35th Street, Chicago, IL 60609 USA Customer Support: (773) 869-1234 NEW! 200412030 93-2431 The Best Mobile Power Solutions for Both RV & Marine Applications! ATTENTION: For Marine Applications, See Inside. Marine Listed Locate and remove the four hex screws on the top panel of your Power Inverter Inverter/Charger as shown. Place the Insulator Drip Shield on the top panel of the Inverter/ Charger. Line up the holes in the shield with the exposed screw holes on the top panel. Using the hex screws, secure the Insulator Drip Shield to the top panel of the Inverter/Charger. Insulator Drip Shield Installation Instructions WARNING! The Insulator Drip Shield is required for installation on your Tripp Lite DC-to-AC Inverter/Charger when it is used in marine applications (e.g. aboard watercraft). Failure to install it as described below may lead to personal injury and/or damage to the Inverter/Charger and connected systems. Installation 1 1 2 3 2 3 Additional Important Safety Instructions! Save These Instructions! These safety instructions augment the instructions listed in the enclosed manual, which focuses upon RV and other land-based applications. Please use this section in addition to page 3R of the owner's manual if you operate the RV1012UL or RV2012UL in a marine installation. In marine applications, a drip shield must be installed; see drip shield instructions listed on the back page for installation information. Important Safety Instructions A) ALL MARINE CONVERTERS IMPORTANT SAFETY INSTRUCTIONS 1) SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for marine converter Models RV1012UL and RV2012UL. 2) CAUTION – To reduce risk of injury, charge only wet cell lead acid or sealed lead acid type rechargeable batteries. Other types of batteries may burst causing personal injury and damage. 3) Do not expose charger to rain or snow. 4) Use of an attachment not recommended or sold by the marine converter manufacturer may result in a risk of fire, electric shock, or injury to persons. 5) Do not disassemble marine converter or inverter; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 6) To reduce risk of electric shock, unplug marine converter or inverter from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. B) MARINE POWER CONVERTERS WITH BATTERY CHARGING FEATURE 1) WARNING – RISK OF EXPLOSIVE GASES. i) WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE SERVICING EQUIPMENT IN THE VICINITY OF THE BATTERY, YOU READ THIS MANUALAND FOLLOW THE INSTRUCTIONS EXACTLY. ii) To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary marking on these products and on engine. 2) PERSONAL PRECAUTIONS i) Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid battery. ii) Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes. iii) Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery. iv) If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, imme...
Эта инструкция также подходит к моделям:Автомобильные аккумуляторы - RV2012UL (243.09 kb)