Keyless Entry Transmitter 1 pc 2.6 x 12 screw 1 pc 2.6 x 6 screw (Batteries inside) 1 pc 2.6 x 25 screw 2. PROGRAM A KEYPAD TO THE RECEIVER You need to do the programming in order to add the keypad transmitter to the receiver. 1 2 3 Plug the receiver 18R (sold separately) into an electrical socket. Press and hold the learn button at the left hand side of the receiver. The red LED on the receiver will flash. Press the [4-digit PIN], [#] and [the assigned number of the door] within 5 seconds. The

Garage Door Receiver Red/Black Wire 2. INSTALLATION The following instructions will show you how to install the receiver. You need to locate 2 things inside your garage to install the receiver: 1) the wall-mounted door control; 2) an electrical outlet, select an electrical outlet different from the one already connected to the power cord of the garage door opener to reduce the chance of interference. The further distance between the receiver and the garage door opener, the less interference betw

If there is no electrical outlet within 20ft of the wall mounted door control, an extension cord can be used for temporary installation. Unplug the power cord of your garage door opener before installation to ensure power is not connected. Wall Mounted Door Control Electrical Outlet WARNING Remove power cord of garage door opener before installation. 1 Remove the wall-mounted door control from the wall by removing the screws. Connect the stripped ends of the Red/Black wire to the 2 terminals (2

Note: The length of the red/black wire is 20ft, so the receiver must be plugged into an electrical outlet that is within 20ft of the wall mounted door control. If there is no electrical outlet within 20ft of the wall mounted door control, an extension cord can be used for temporary installation. 2. INSTALLATION (CONT) 2 3 3. TROUBLE SHOOTING Q: Door opener does not react after pressing the button on the transmitter. A:- Ensure you hear 3 beeps from the keypad transmitter after entering the defau

Otherwise, check if the battery is inserted properly. -The left button on the transmitter should be pressed, not the right button -If the red light on the receiver flashes when you press the left button on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control. -Ensure the wires that are previously connected to the wall mounted door control are not loose. -Ensure the code setting on the

Wireless Switch ReceiverGarage Door Mounting Bracket Clip Keychain Transmitter (Battery inside) Receiver Red/Black Wire 2. INSTALLATION OF GARAGE DOOR RECEIVER The following instructions will show you how to install the receiver. After installing, the keychain transmitter (already programmed to the receiver) can be used to operate your garage door opener. You need to locate 2 things inside your garage to install the receiver: 1) the wall-mounted door control; 2) an electrical outlet, select an e

101A393 DEC, 2005 English English Swing Door Opener USER'S INSTRUCTIONS CONTENT CONTENT Introduction.......................................................................................................................................................................................4 Overview.....................................................................................................................................................................................4 Installation - In Swing.

3.2 Place the operator onto the mounting plate based on the door type. For instance, for in-swing left door, the “IN-SWING LEFT” holes should match the 2 top holes of the operator. 3.3 Secure the operator to the mounting plate with 6 nuts, spring washers and bolts. Slider bracket Note: In-Swing right door installation shown. Note: In-Swing left door installation shown. For In-Swing Left installation, place the top 2 screws of the door opener to these 2 holes. WARNING To avoid possible serious in

The Model G6K works with the Skylink® Garage Door Receiver, such as Smart ButtonTM and EQ / IQ Garage Door Opener. In this package, you will find a keyless entry transmitter with 3V lithium batteries and screws. Garage Door 1 pc 2.6 x 6 screw Remote Control 1 pc 2.6 x 12 screw (Batteries inside) 1 pc 2.6 x 25 screw 2. PROGRAM A KEYPAD TO A GARAGE DOOR RECEIVER Before proceeding, please remove the battery isolator from the keypad transmitter. The keypad transmitter can operate up to 4 garage door

INSTALLATION Unplug the power cord of your garage door opener WARNING before installation to ensure power is not connected. GTR Smart ButtonTM The GTR Smart ButtonTM replaces most garage door “push buttons” or “wall consoles”. There are 2 different kinds of “push buttons”. 1) Single button 2) Multi-Function Wall Console 1) Single button If your garage door opener comes equipped with a single button “push button”, you can replace the existing push button with Skylink® Smart ButtonTM GTR. Please f