Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on page 7. 3. Is there a build-up of ice or snow under the door? The door may be frozen to the ground. Remove any restriction. 4. The garage door spring may be broken. Have it replaced. 5. Repeated operation may have tripped the overload protector in the motor. Wait 15 minutes. Try again. Opener operates from 1. Is the door control lit? If not, remove the bell wire from the opener terminals. Short the the remote, but not red and white terminals by touching both terminals at the same time with a piece of from Door Control: wire. If the opener runs, check for a faulty wire connection at the door control, a short under the staples, or a broken wire. 2. Are the wiring connections correct? Review Step 6, page 14. The door operates 1. Is the door push bar flashing? If your model has the Lock feature, turn it off. from the Door 2. Your opener needs to re-learn a remote control code. Refer to instructions on the Control, but not from opener panel. the remote control: 3. Program the receiver to match the remote control code. 4. Repeat the receiver programming procedure with all remote controls. The remote control 1. Change the location of the remote control in your car. has short range: 2. Check to be sure the antenna on the side or back panel of opener extends fully downward. 3. Some installations may have shorter range due to a metal door, foil backed insulation, or metal garage siding. Opener noise is If operational noise is a problem because of proximity of the opener to the living disturbing in living quarters, the Vibration Isolator Kit 41A3263 can be installed. This kit was designed to quarters of home: minimize vibration to the house and is easy to install. The garage door 1. Be sure that all remote control push buttons are off. opens and closes 2. Remove the bell wire from the door control terminals and operate from the remote by itself: only. If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between the door control and the opener. 3. Clear memory and reprogram all remote controls. The door doesn't 1. If the door has been working properly but now doesn't open all the way, increase the open completely: up force.See page 25. 2. Is something obstructing the door? Remove the obstruction or repair the door. 3. If door opens at least 5 feet, the travel limits may need to be increased. One turn equals 2 inches of travel. See page 24. Repeat the safety reverse test after the adjustment is complete. The door stops but Review the travel limits adjustment procedures on page 24. doesn't close Repeat the safety reverse test after any adjustment of door arm length, close completely: force or down limit. 30 Having a Problem? (continued) Situation Probable Cause & Solution Having a Problem? (continued) Situation Probable Cause & Solution 2. If the opener lights do not blink and it is a new installation, check the down force. See Adjustment Step 2, page 25. For an existing installation, see below. Repeat the safety reverse test after the adjustment is complete. The door reverses for no apparent reason and opener lights don't blink: 1. Is something obstructing the door? Pull the manual release handle. Operate the door manually. If it is unbalanced or binding, call for professional garage door service. 2. Clear any ice or snow from the garage floor area where the door closes. 3. Review the force adjustment procedures on page 25. 4. If door reverses in the fully closedposition, decrease the travel limits (page 24). Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment of the force and limit settings is normal. Weather conditions in particular can affect door travel. The door reverses for Check the safety reversing sensor. Remove any obstruction or align the receiving eye. no apparent reason See page 19. and opener lights blink for 5 seconds after reversing: The opener lights: . . . don't turn on: Replace the light bulbs (75 watts maximum). Use a standard neckgarage door opener bulb if regular bulb burns out. . . . don't turn off: Is the Light feature on? Turn it off. The opener strains or maximum force is needed to operate door: The door may be out of balance or the springs are broken. Close the door and use the manual release to disconnect the trolley. Open and close the door manually. A properly balanced door will stay in any point of travel while being supported entirely by its springs. If it does not, disconnect the opener and call a professional garage door serviceman. Do not increase the force to operate the opener. The opener motor hums briefly, then won't work: 1. The garage door springs are broken. See above. 2. If the problem occurs on the first operation of the opener, door may be locked. Disable the door lock. If t...