Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
(NOT PROVIDED) Door Bracket Vertical Centerline UP Vertical Reinforcement Self-Threading Screw 1/4"-14x5/8" Door Bracket Nut 5/16"-18 Bolt 5/16"-18x2" Lock Washer 5/16" Vertical Centerline UP Vertical Reinforcement Figure 2B UP Vertical Centerline Self-Threading Screw 1/4"-14x5/8" Figure 3 UP Inside Edge of Door or Reinforcement Board Bolt 5/16"x2" Vertical Centerline Figure 4 Self-Threading Screw 1/4"-14x5/8" HARDWARE SHOWN ACTUAL SIZE 20 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Metal Doors:Drill 3/16" pilot holes and fasten the bracket with the 1/4"-14x5/8" self-threading screws provided. • Wood Doors:Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or 5/16"x1-1/2" lag screws (not provided) depending on your installation needs. NOTE:The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.) Self-Threading Screw 1/4"-14x5/8" HARDWARE SHOWN ACTUAL SIZE Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use 5/16"x1-1/2" lag screws (not provided) to fasten door bracket. METAL DOOR Top of Door (Inside Garage) Door Bracket Optional Placement Top Edge of Door 1/4"-14x5/8" Self-Threading Screw Door Bracket Top of Door (Inside Garage) Carriage Bolt 5/16"x2" (Not provided) Optional Placement Lock Washer 5/16" Nut 5/16"-18 Top Edge of Door WOOD DOOR HORIZONTAL AND VERTICAL REINFORCEMENT IS NEEDED FOR LIGHTWEIGHT GARAGE DOORS (FIBERGLASS, ALUMINUM, STEEL, DOORS WITH GLASS PANEL, ETC). (NOT PROVIDED) 21 INSTALLATION STEP 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in Figures 1, 2 and 3. • Figure 1: – Fasten straight door arm section to outer trolley with the 5/16"x1" clevis pin. Secure the connection with a ring fastener. – Fasten curved section to the door bracket in the same way, using the 5/16"x1-1/4" clevis pin. • Figure 2: – Bring arm sections together. Find two pairs of holes that line up and join sections. Select holes as far apart as possible to increase door arm rigidity. • Figure 3, Hole alignment alternative: – If holes in curved arm are above holes in straight arm, disconnect straight arm. Cut about 6" from the solid end. Reconnect to trolley with cut end down as shown. – Bring arm sections together. – Find two pairs of holes that line up and join with screws, lock washers and nuts. • Proceed to Adjustment Step 1, page 24. Trolley will re-engage automatically when opener is operated. Ring Fastener Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm Straight Door Arm Clevis Pin 5/16"x1" Inner Trolley Outer Trolley Figure 1 Figure 2 Lock Washers 5/16" Nuts 5/16"-18 Door Bracket Screws 5/16"-18x7/8" Emergency Release Handle Lock Washers 5/16" Nuts 5/16"-18 Screws 5/16"-18x7/8" Cut This End Lock Washer 5/16"Nut 5/16"-18 Ring Fastener Hex Screw 5/16"-18x7/8" Clevis Pin 5/16"x1" (Trolley) Clevis Pin 5/16"x1-1/4" (Door Bracket) HARDWARE SHOWN ACTUAL SIZE Figure 3 22 ALL ONE-PIECE DOORS 1.Assemble the door arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener. 2.Adjustment procedures: On one-piece doors, before connecting the door arm to the trolley, the travel limits must be adjusted. Limit adjustment screws are located on the left side panel as shown on page 24. Follow adjustment procedures below. • Open door adjustment: decrease UP travel limit – Turn the UP limit adjustment screw counterclockwise 5-1/2 turns. – Press the Door Control push bar. The trolley will travel to the fully open position. – Manually raise the door to the open position (parallel to the floor), and lift the door arm to the trolley. The arm should touch the trolley just in back of the door arm connector hole. Refer to the fully open trolley/door arm positions in the illustration. If the arm does not extend far enough, adjust the limit further. One full turn equals 2" of trolley travel. • Closed door adjustment: decrease DOWN travel limit – Turn the DOWN limit adjustment screw clockwise 5 complete turns. Door Bracket Ring Nuts 5/16"-18 Lock Washers 5/16" Fastener Straight Arm Screws 5/16"...
Эта инструкция также подходит к моделям:Автоматические ворота - 1265-267 1/2 HP (1.09 mb)