Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации Craftsman, модель SECURITY+ 139.53683

Производитель: Craftsman
Размер: 107.32 kb
Название файла: 126bc388-f247-4b30-99d0-4853a1076ea6.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Install the receiver (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control(s). A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see it clearly, and there are no obstructions to door travel• DISCONNECT POWER TO THE GARAGE DOOR OPENER REFOREPROCEEDING. The SECURITY+ Universal Remote Control Conversion Kit consistsof a receiver and remote control(s). This accessory will convert almost any garage door opener to rollingcode technology. The remote control sends a coded signal from outside the garage. Inside the garage, the plug-inreceiver accepts the transmittedsignal and starts the door opener. With Security+, the code between the remote control and the receiver changes with each use, accessing over 100 billion new codes. IMPORTANT: To improve the security of your opener, discard your old remote controls end erase or reset your code. For maximum security and range, you must disable the existing receiver on your opener, otherwise it could still activate your opener: • If there is an external receiver, disconnect power to it. • If it is an integrated receiver, either clip off the component that feeds power to the receiver or remove the tuning slug and antenna from the receiver section. If you have a different brand of opener, contact the manufacturer for additional information on disabling the existing receiver. • If you have a Sears opener with an SRT receiver, erase the old codes by holding down the SRT button for 6 seconds until the indicator light turns off. • If you have code switches, reset them to a random code and deactivate the receiver as follows: On the opener panel, peel back the lower right _ I_ I_ corner of the label to Cut Antenna expose the tuning slug (closest to the antenna), as shown. Tuning Remove the slug --Slug with a small hex .Peal beck label at comet head wrench and cut the antenna wire. SECURITY,F Universal Remote Control Conversion Kit Model 139.53682 (With I Remote Control) Model 139.53683 (With 2 Remote Controls) To complywith Fco rules,adjustmentsor modificationsof thr= reseivorand,/or transmitterare prohibited,except for changingthe code set_g o_replacing the ransmittorbattery.THERE ARE NO USER SERV CEABLE PARTS. NOTICE TO U. S. CONSUMERS: Some stat_sprohibittheserviceor repairofgaragedooropeners wbchcannotbe madeto complywiththe safetystandardscontained inUL325 (1988 revision).Inordertocomplywithboththeletterand the spiritof these laws, this universalremote conttol converterkit shouldnotbe used with any Sears Craftsman= garage door opener manufacturedpdorto Apdl1, 1982. Power.. !Terminals Aotuator Cover Indicator "o _11 Wire SRT ._ Indicator ght --_ Illico.. act Bell Wire Light L._ to Garage DoorI •"_--Opener Terminals SRT (learn) Antenna Actuator Belllwira OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown• Twist up actuator cover. CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver scre...

Эта инструкция также подходит к моделям:
Автоматические ворота - SECURITY+ 139.53682 (107.32 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории