Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details. IMPORTANT !!! Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling. However, there are some limitations which must be observed. • For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. • A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. • Changes or modifi cations to the device may void FCC compliance. • Infrequently used radio links should be tested regularly to protect against undetected interference or fault. • A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. • This device complies with FCC Part 15 and Industry Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (760) 438-7000 • FAX (760) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free FAX (800) 468-1340 RETAINING SCREW RELAY OUTPUT TERMINALS 1 AMP @ 32 VDC MAXIMUM ANTENNA LEARN BUTTON LEARN & SIGNAL INDICATOR AC POWER TERMINALS BEST RECEPTION GOOD RECEPTION POOR RECEPTION A PLUG CLOSE TO GROUND LEVEL WILL CAUSE POOR RADIO RECEPTION A PLUG ABOVE THE GROUND LEVEL WILL PROVIDE GOOD RADIO RECEPTION A PLUG ON THE CEILING WILL GIVE THE BEST RADIO RECEPTION (UNLESS THE OPERATOR'S RECEIVER CAUSES SOME INTERFERENCE) WATCH THE MDR-U RECEIVER'S LEARN INDICATOR IF THE LEARN INDICATOR IS FLASHING WITHOUT ACTIVATING ANY TRANSMITTERS, INTERFERENCE MAY BE COMING FROM A NEARBY OPERATOR'S RECEIVER TEST IF THE OPERATOR IS THE SOURCE OF THE INTERFERENCE BY UN-PLUGGING THE OPERATOR FROM POWER IF THE LEARN INDICATOR STOPS FLASHING, THE OPERATOR IS THE SOURCE OF INTERFERENCE 1. IF THE OPERATOR HAS AN EXTERNAL RADIO RECEIVER, DISCONNECT POWER TO IT 2. IF THE OPERATOR HAS A BUILT-IN RADIO RECEIVER, CUT THE COMPONENT THAT FEEDS POWER TO THE RECEIVER OR CUT OFF THE OPERATOR'S ANTENNA AND REMOVE THE RECEIVER'S TUNING SLUG NOTE: IT IS RECOMMENDED TO DISABLE THE OPERATOR'S RECEIVER TO PREVENT THE OLD REMOTES FROM ACTIVATING IT OPERATOR'S ANTENNA CONNECT 2-CONDUCTOR WIRE TO THE MDR-U RECEIVER RELAY OUTPUT TERMINALS FROM OPERATOR PUSHBUTTON MDR-U ANTENNA WALL PUSHBUTTON CONNECTION DIRECT OPERATOR CONNECTION ROUTE THE WIRE AND CONNECT IT TO EITHER THE WALL PUSHBUTTON OR DIRECTLY TO THE DOOR OPERATOR (POLARITY NOT IMPORTANT) OPERATOR TERMINALS 1 & 2 (OR THE SAME TERMINALS THE WALL PUSHBUTTON USES) 3 2 1 SECURE THE WIRE WITH INSULATED STAPLES DISCONNECT POWER TO THE GARAGE DOOR OPERATOR BEFORE PROCEEDING UL NOTE: ALL LOW VOLTAGE CLASS 2 CABLE USED WITH THE OPERATOR MUST BE UL LISTED TYPE CL2, CL2P, CL2R, OR CL2X OR OTHER CABLE WITH EQUIVALENT OR BETTER ELECTRICAL, MECHANICAL, AND FLAMMABILITY RATINGS REMOVE THE OUTLET'S COVER PLATE SCREW AND PLUG THE RECEIVER INTO THE 110 VAC OUTLET SECURE THE RECEIVER TO THE OUTLET WITH THE RETAINING SCREW NOTE: BE SURE THAT THE OUTLET IS NOT CONTROLLED BY A WALL SWITCH ADDING TRANSMITTERS ERASING TRANSMITTERS 1. PRESS AND RELEASE THE LEARN BUTTON 2. THE LEARN INDICATOR WILL LIGHT IF THERE'S ROOM IN MEMORY (UP TO 10 TRANSMITTERS WILL FIT) 3. ACTIVATE THE TRANSMITTER WHILE THE INDICATOR IS LIT (WITHIN 15 SECONDS) 4. INDICATOR FLASHES 5. REPEAT STEPS FOR ADDITIONAL TRANSMITTERS 1. PRESS AND HOLD DOWN THE LEARN BUTTON 2. THE LEARN INDICATOR WILL FLASH COUNTING THE NUMBER OF TRANSMITTERS IN MEMORY 3. CONTINUE HOLDING DOWN THE LEARN BUTTON 4. 5 SECONDS AFTER THE COUNT THE INDICATOR WILL FLASH ONCE SHOWING THE MEMORY ERASURE 5. RELEASE THE BUTTON, THE UNIT ENTERS LEARN MODE FOR 15 SECONDS TEST RECEIVER ACTIVATE EACH TRANSMITTER AND VERIFY THAT THE RECEIVER AND DOOR ...