Оценок - 2, средний балл: 5 ( )

Производитель: Chamberlain Размер: 2.37 mb Название файла: Язык инструкции:

Short the red and white terminals by touching both terminals at the same time with a piece of wire. If the opener runs, check for a faulty wire connection at the door control, a short under the staples, or a broken wire. • Are wiring connections correct? Review page 3. 3. Door operates from door control but not from remote: • Check battery. Replace battery if necessary. • Is the light at the wall control flashing? Press button with key-symbol to unlock the opener against remote controls. • Is the receiver LED flashing at the back-side of the opener when the transmitter is pressed? The opener receiver must re-learn the remote control code. Follow the instructions on page 4. • If you purchased a new remote control then check at carton of remote control for compatibility or call the Service Hotline. 4. Remote has short range: • Is battery installed? If needed, change the battery. • Change the location of the remote control on the car. • A metal garage door, foil-backed insulation or metal siding will reduce the transmission range. • Use outside coaxial antenna adapter to move antenna. 5. Door reverses for no apparent reason and opener light doesn't blink: • Is something obstructing the door? Pull manual release handle. Operate door manually. If it is unbalanced or binding, call for professional garage door service. • Clear any ice or snow from garage floor area where garage door closes. • Review Force Settings. Open and close the door in learn mode for several (3-5) consecutive cycles to allow the operator to adjust to inconsistent doors. • If door reverses in FULLY CLOSED position, re-learn travel limits. Repeat safety reverse test after adjustment is complete. The need for occasional adjustment of the force and limit settings is normal. Weather conditions in particular can affect door travel. 6. Door reverses for no apparent reason and opener light blinks for 5 seconds after reversing: Check The Safety Infrared Reversing Sensor (if you have installed this accessory). If the light is blinking, correct alignment. Note: Continuously holding down the door control button will allow the door to close if the protector system is not properly aligned. The transmitter will not close the door. The opener lights will blink. 7. Opener noise is disturbing in living quarters of home: If operational noise is a problem because of proximity of the opener to the living quarters, Vibration Isolator Kit 062155 (included with the operator) can be installed. This kit was designed to reduce the "sounding board effect" and is easy to install. 8. The garage door opens and closes by itself: • Delete all remote controls and reprogram. • Make sure remote push button is not stuck "on". • Disconnect all push buttons or key switches attached and wait one day. 9. Door stops but doesn't close completely: Review Limit Adjustment section. Repeat safety reverse test after any adjustment of door arm length, close force or down limit. 10. Door opens but won't close: • Check The Safety Infrared Reversing Sensor (if you have installed this accessory). If the light is blinking, correct alignment. • If opener light does not blink and it is a new installation, check the down force. Repeat the safety reverse test after the adjustment is complete. 11. Opener light does not turn on: Replace light bulb (40 Watts maximum). Replace burned out bulbs with rough service light bulbs. 12. Opener light does not turn off: There may be a defective earth at the ceiling or wall receptacle. The unit must be earthed. 13. Opener strains or reversed during opening: Door may be unbalanced or springs are broken. Close door and use manual release rope and handle to disconnect trolley. Open and close door manually. A properly balanced door will stay in any point of travel while being supported entirely by its springs. If it does not, call for professional garage door service to correct the problem. Do not change force settings. 14. Opener motor hums briefly, then won't work: • Garage door springs are broken. SEE ABOVE. • If problem occurs on first operation of opener, door is locked. Disable door lock. If chain was removed and reinstalled, the motor may be out of phase. Remove chain; cycle motor to down position. Observe drive sprocket. When it turns in clockwise direction and stops in down position, re-install chain. Repeat safety reverse test after adjustment is complete. 15. Opener won't activate due to power failure: • Pull manual release rope and handle down and back to disconnect trolley. Door can be opened and closed manually. When the power is restored, pull the manual release handle straight down. The next time the opener is activated, the trolley will reconnect. • The Outside Quick Release accessory (if fitted) disconnects the trolley from outside the garage in case of power failure. 114A2845 30 PROGRAMMING Below are instructions for programming your opener to operate with remote control transmitters. To Code a Hand-held Remote Control Transmitter USING THE “SMART”...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: