Войти:
Оценок - 3, средний балл: 3.3 ( )

Инструкция по эксплуатации Chamberlain, модель 1160- 1/2 HP

Производитель: Chamberlain
Размер: 1.25 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Operate door in DOWN direction. The door MUST reverse on the obstruction. If the door STOPS on the obstruction, it is not traveling far enough in the DOWN direction. Increase the DOWN limit by turning DOWN limit adjustment screw counterclockwise 1/4 turn. REPEAT TEST. NOTE: Make sure limit adjustments do not force the door arm beyond a straight up and down position. See the illustration on Page 18/19. When the door reverses on the one-inch obstacle, remove the obstruction and run the opener through a complete travel cycle. Door MUST NOT reverse in closed position. Repeat Adjustment Steps 1, 2 and 3 if necessary. THE PROTECTOR SYSTEM™ OO Installation of Optional Safety Feature THE PROTECTOR SYSTEM PROVIDES AN ADDITIONAL MEASURE OF SAFETY AGAINST A SMALL CHILD BEING CAUGHT UNDER A GARAGE DOOR. It uses an invisible beam which, when broken by an obstruction, causes a closing door to open and prevents an open door from closing. STRONGLY RECOMMENDED FOR HOMEOWNERS WITH YOUNG CHILDREN. After opener has been installed and adjusted, THE PROTECTOR SYSTEM accessory can be installed. Instructions are included with this optional device. 22 Radio Controls F.C.C. rules prohibit adjustments to or modification of receiver and/or remote control transmitter circuitry except for changing the code setting and replacing the remote control transmitter battery. THERE ARE NO USER SERVICEABLE PARTS. Manufactured under 1 or more of the following U.S. patents: RE29,525: 4,037,201; 4.750.118: 4.806.930 Other Patents Pending ACTIVATE THE OPENER ONLY WHEN DOOR IS IN FULL VIEW, FREE OF OBSTRUCTION AND PROPERLY ADJUSTED . NO ONE SHOULD ENTER OR LEAVE GARAGE WHILE DOOR IS IN MOTION. DO NOT ALLOW CHILDREN TO OPERATE REMOTES OR DOOR CONTROL BUTTONS. DO NOT ALLOW CHILDREN TO PLAY NEAR THE DOOR. Your garage door opener receiver and remote control transmitter have been set at the factory to a matching code. If you want to CHANGE your code or purchase additional remotes, follow the Instructions below. The code in any NEW remote control must be set to match the code in the original remote control. MATCH/CHANGE THE CODE IN REMOTE CONTROL(S) SET CODE SWITCHES IN ALL REMOTES TO MATCHING POSITIONS PROCEDURE: Slide battery compartment cover back to access the code switches in your single function remote control and any new remote control Place remote controls side by side as shown and set code switches in ALL remotes to matching positions (+, -, 0). Use a pen or screwdriver to slide the switches. NOTE: Instructions for matching the code switches in two-channel and multi-function remote control transmitters are included with those accessories. MATCH/CHANGE THE CODE IN THE RECEIVER GARAGE DOOR OPENERS WITH RECEIVER SMART CODE BUTTON 1. Press the RECEIVER Smart Button on the back panel of the opener as shown The adjacent indicator light will turn ON. CAUTION: Door will begin to move immediately if any transmitter has been activated. If this occurs, wait until the door has completed its UP or DOWN cycle. Then begin again at Step 3. 2. STAND AWAY FROM THE DOOR and press the remote Push Button control transmitter push button The indicator light will turn OFF REMOTE CONTROLTRANSMITTER and the door will move. Receiver and remote control(s)...

Эта инструкция также подходит к моделям:
Автоматические ворота - 1145- 1/3HP (1.25 mb)
Автоматические ворота - 1146 - 1/3HP (1.25 mb)
Автоматические ворота - 1150- 1/3HP (1.25 mb)
Автоматические ворота - 1155 - 1/2HP (1.25 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории