Оценок - 3, средний балл: 3.7 ( )

Производитель: Sears Размер: 2.32 mb Название файла: Язык инструкции:

If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. To avoid installation difficulties, do not run the opener at this time. To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. Do NOT use an extension cord, 2-wire adapter, or change the plug in any way to make it fit your outlet. Right Wrong If permanent wiring is required by your local code, refer to the following procedure: Permanent To make a permanent connection through the 7/8" diameter hole in the top of the opener (according to local code): Wiring Connections • Remove the opener cover screws and set the cover aside. • Remove the attached 3-prong cord. • Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded. • Reinstall the cover. Ground Green Ground Screw Wire Tab Black Wire White Wire Black Wire To avoid installation difficulties, do not run the opener at this time. 2O The Safety Reversing System Information you'll need before you begin the The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. This is a required safety device and cannot be disabled. Installation procedures are the same for sectional and one-piece doors. Be sure power to the opener is disconnected. The sending eye transmits an invisible light beam to the receiving eye. The units can be installed on either side of the garage door as long as the sun never shines directly into the receiving eye lens. Look at the label on the connector end of each case to identify the sensors. The brackets must be connected and fastened so that the sending and receiving eyes face each other as shown in Figure 1. If an obstruction breaks the light beam while the garage door is closing, the door will stop and reverse to full open position and the opener lights will flash for 5 seconds. installation of the safety reversing sensor. Without a properly working safety reversing sensor, persons (particularly children) could be injured or killed by a closing garage door. Read and follow all instructions, To protect small children, install the safety reversing sensor so that the beam will be no higher than 4"-6" above the garage floor. Disconnect power to the garage door opener before installing the safety reversing sensor. The brackets must be securely fastened to a solid surface such as the studs on either side of the door, or add a piece of wood at each location if installing in masonry construction. The invisible light beam path must be unobstructed. No part of the garage door (or door tracks, springs, hinges, rollers or other hardware) can interrupt the beam while the door is closing. If it does, use a piece of wood to build out each sensor mounting location to the minimum depth required for light beam clearance. Sensor Beam Sensor Beam 4-6" max 4-6" max. above floor above floor Invisible Light Beam Protection Area Figure 1: Facing the door from inside the garage 21 Installation Step 10 install the Safety Reversing Sensor Figures 2 and 3 show assembly of brackets and Figure 2 Mounting Bracket "C" wrap based on the recommended installation of With Holes Square the sensors as shown on page 21. / "C" Wrap However, Figures 4 and 5 are variations which may fit your installation requirements better. Make sure the wraps and brackets are aligned so the #10-32 sensors will face each other across the garage Lock Nuts door. #10-32x3/8" • Fasten the "C" wraps to the mounting brackets Screws having square holes, using the hardware shown in Figure 2. • Connect each assembly to a slotted bracket, using Figure 3 the hardware shown in Figure 3. Note the alignment of the brackets for left and right sides of the door. 1/4x1-1/2" 1/4-20xl/2" Carriage Bolts • Finger tighten the lock nuts. Lag Screws (with square shoulder) Inside • Use bracket mounting holes as a template to Garage -locate and drill (2) 3/16" diameter pilot holes on Wa both sides of the garage door, 4"-6" above the floor but not exceeding 6". (See warning on page 21 .) • Attach bracket assemblies with 1/4"x1-1/2" lag screws as shown in Figure 3. g Bracket "C" Wrap ,vith Slot • Adjust right and left side bracket assemblies to the /1/4 _ Mounting Bracket same distance out from the mounting surface. Make sure all door hardware obstructions are / % 20 _otes cleared. Tighten the nuts securely. // Lock Nuts Hardware Shown Actual Size © © _ I IIII IIIll/[Ix!_11!I,I I IIII I_'_ #10-32x3/8" #10x32 1/4"-20x 1/2" 1/4"-20 Screw Lock Nut Lag Screw Staples Carriage Botts Lock Nut Alternate Wall Mount Figure 5 Alternate Floor Mount Inside Garage I Mounting Bracket with Slot Mounting Bracket with Square Holes Wail sensorIndicator Light Mounting Bracket with Square HoIes j/J Sensor Indicator Light ,C!' Wrap Mounting Bracket with Slo...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: