Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
LEARN SENSOR TO AAA+TM CONTROL PANEL (CONT) The garage door monitorTM sensor is designed to monitor the status of your garage door and advise you if the door is open. It works in conjunction with AAA+TM Control Panel. When the monitored door is opened, the control panel will either alert you or alarm will be triggered. In this package, you should find a garage door monitorTM sensor, 3V lithium battery and other mounting accessories. Sensor Mounting plate 3V Lithium battery 2 pcs 3.5 x 18 screws 2 pcs 3.5 x 12 screws Please follow the instructions below to set up the garage door monitorTM sensor. 2. LEARN SENSOR TO AAA+TM CONTROL PANEL In order for the sensor to communicate with the control panel properly, the sensor must be programmed to the control panel. Follow the brief instructions below or refer to the detail instructions from the AAA+TM User’s Instructions to program the sensor to the control panel. Before proceeding, please remove the battery isolator from the sensor. Step Keys Function Description Note 1 [PROG] [MPIN] Enter Programming mode Enter master password to programming mode 3 beeps for valid password. 1 long beep for invalid password. 2 [3] Select learn sensor After [3] is entered, some zone LEDs will programming flash once, or twice, some will be off. The zone LEDs represent whether that zone is already occupied by another sensor. **See Table A below. 3 [0] to [9] Select sensor location Refer to the diagram below to After you have selected the zone, select the sensor that zone LED will location, which includes the zone be on. and sensor number. 4 Activate the sensor by tilting the sensor from horizontal to vertical position Activate sensor Once the sensor is activated, the signal will be transmitted to the Control Panel which will be stored. You will hear [Zone X Sensor Y Accepted ], where X and Y are the zone and sensor numbers you have selected. This row : Buttons for Sensor 1 Zone LED : Flash once This row : Buttons for Sensor 2 Zone LED : Flash twice ® SENSOR 1 SENSOR 2 Zone 1 Button [1] Button [6] Zone 2 Button [2] Button [7] Zone 3 Button [3] Button [8] Zone 4 Button [4] Button [9] Zone 5 Button [5] Button [0] Note: Each location is allowed to learn one sensor only. Learning a sensor to a location will clear the memory of the sensor previously learnt. ZONE LED DESCRIPTION Off Zone is not occupied by any sensor Flashes once This zone is occupied by sensor 1. Flashes twice This zone is occupied by sensor 2. Flashes once, then twice This zone is occupied by sensors 1 and 2. ** Table A: Zone LED status for learning sensors. After learning the sensor to the control panel, you may test the communication by placing the sensor in vertical position & horizontal position. Horizontal Vertical When the sensor is in vertical position, When the sensor is in horizontal position, the the receiver will not beep. receiver will beep and a zone LED will flash. If the sensor is face up in the vertical position, the control panel will not beep, indicating the sensor is in a closed position. If the sensor is face down in the horizontal position, the control panel will beep and a zone LED will flash to indicate a door is open. You can change the orientation of the sensor and you should see the change in response of the receiver. If the sensor and receiver are working properly in close proximity, you can now begin to install the sensor onto your garage door. NOTE: It is normal to hear a rattle from the sensor when tilted or rotated to another position. The control panel will announce the sensor's status, such as "Zone 1 Sensor 1 Triggered", and corresponding zone LED will flash and buzzer will beep. If the magnetic contact is closed, the beeping will stop. 3. INSTALLATION WARNING Unplug the power cord of your garage door opener before installation to ensure power is not connected. Attached the sensor to the garage door with double-sided foam tape if the surface of your garage door is smooth and clean enough to provide a good adhesive surface, such surface can usually be found on a metal garage door. Please ensure the surface is smooth and clean. For wooden garage doors, it is recommended to use the mounting plate and screws as well. Double-sided foam tape Mounting plate and screws (optional) Sensor Note: Mount the sensor near the top of the garage door for best results. Note: Ensure you straighten up the antenna on the receiver to receive the best possible reception. 8. WARRANTY 4. OPERATION 8. WARRANTY 4. OPERATION Garage door monitorTM sensor is used to monitor garage door. When the door is open or closed, the sensor will transmit a signal to the control panel to notify the user. After mounting the sensor, test the sensor by opening and closing the garage door. Open the garage door will result in the followng: 1. Voice announcement - Announce the triggered zone and sensor 2. Beeping - The number of beep represents the zone number 3. Zone LED flashing - Number of flash represents the sensor number. 5. SENSOR...