Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Panasonic, модель CQDF401U

Производитель: Panasonic
Размер: 727.81 kb
Название файла:
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


E
E
N
N
Installation Guide (Continued)
G
G
L
L
I
I
S
S
If your car is not wired for an audio unit:
Speakers
H
Identify All Leads
Final Checks
H
Go to the fuse block and find the fuse port for the
Connect the speaker wires. See the wiring diagram
The first step in installation is to identify all the car
1. Make sure that all wires are properly connected
11
12
battery, usually marked BAT.
(➡ pages 25, 26) for the proper hookups. Follow
wires you’ll use when hooking up your sound sys-
and insulated.
the diagram carefully to avoid damaging the speak-
tem.
Speakers
2. Make sure that the stereo unit is securely held in
ers and the stereo unit.
As you identify each wire, we suggest that you label
Identify the car speaker leads. There are two leads
the mounting collar.
The speakers used must be able to handle more
it using masking tape and a permanent marker.
for each speaker which are usually color coded.
3. Turn on the ignition to check the unit for proper
than 45 W of audio power. If using an optional
This will help avoid confusion when making con-
A handy way to identify the speaker leads and the
operation.
audio amplifier, the speakers should be able to han-
nections later.
speaker they are connected with is to test the leads
dle the maximum amplifier output power. Speakers
If you have difficulties, consult your nearest author-
using a 1.5 V AA battery as follows.
Note:
with low input ratings can be damaged. Speaker
ized professional installer for assistance.
Hold one lead against one pole of the battery and
≥ Do not connect the power connector to the stereo
impedance should measure 4–8
stroke the other lead across the other pole. You will
≠, which is typi-
unit until you have made all connections. If there
cally marked on most speakers. Lower or higher
hear a scraping sound in one of the speakers if you
Preparation
are no plastic caps on the stereo hooking wires,
impedance speakers will affect output and can
are holding a speaker lead.
insulate all exposed leads with electrical tape until
cause both speaker and stereo unit damage.
≥ We strongly recommend that you wear gloves
If not, keep testing different lead combinations until
you are ready to use them. Identify the leads in
for installation work to protect yourself from
you have located all the speaker leads. When you
Motor Antenna
the following order.
injuries.
label them, include the speaker location for each.
Connect the car motor antenna lead to the dark
Power Lead
≥ When bending the mounting tabs of the
blue motor antenna relay control lead.
Antenna Motor
If your car has a radio or is pre-wired for one:
mounting collar with a screwdriver, be careful
If your car is equipped with an automatic power an-
Battery
Cut the connector wires one at a time from the plug
not to injure your hands and fingers.
tenna, identify the car motor antenna lead by con-
Connect the yellow battery lead to the correct radio
(leaving the leads as long as possible) so that you
necting one bulb tester lead to the car battery lead
wire or to the battery fuse port on the fuse block.
can work with individual leads.
≥ Disconnect the cable from the negative - battery
and touching the remaining exposed wires from the
Antenna
terminal (see caution below).
cut radio connector plug one at a time. You will
Connect the antenna by plugging the antenna lead
≥ Unit should be installed in a horizontal position
hear the antenna motor activate when you touch
into the antenna receptacle.
with the front end up at a convenient angle, but
the correct wire.
not more than 30o.
Equipment
Antenna
Connect any optional equipment such as an ampli-
Turn the ignition on to the accessory position, and
The antenna lead is a thick, black wire with a metal
fier, according to the instructions furnished with
ground one lead of the test bulb to the chassis.
plug at the end.
the equipment. Leave about 12z (30 cm) of dis-
Touch the other lead of the test bulb to each of the

tance between the speaker leads/amplifier unit and
Less than 30x
exposed wires from the cut radio connector plug.
Connect All Leads
the antenna/antenna extension cord. Read the oper-
Touch one wire at a time until you find the outlet
Now that you have identified all the wires in the car,
ating and installation instructions of any equipment
that causes the test bulb to light.
you are ready to begin connecting them to the
you will connect to this unit.
stereo unit wires. The wiring diagram (➡ pages 25,
Caution:
Now turn the ignition off and then on. If the bulb
26) shows the proper connections and color coding
Power
≥ Do not disconnect the battery terminals of a
also turns off and on, that outlet is the car power
of the leads.
Connect the red power lead to the correct car radio
car with a trip or navigational computer since
lead.
We strongly recommend that you test the unit be-
wire or to the appropriate fuse port on the fuse
all user settings stored in memory will be lost.
If your car is not wired for an audio unit:
fore making a final installation.
block.
Instead take extra care with installing the unit
Go to the fuse block and find the fuse port for radio
You can set the unit on the floor and make tempo-
If the stereo unit functions properly with all these
to prevent shorts.
(RADIO), accessory (ACC), or ignition (IGN).
rary connections to test the unit. Use electrical tape
connections made, disconnect the wires and pro-
to cover all exposed wires.
ceed to the final installation.
Dashboard Installation
Battery Lead
Installation Opening
If your stereo unit has a yellow lead, you will need
Important:
Final Installation
to locate the car’s battery lead. Otherwise you may
23/
≥ Connect the red power lead last, after you
Lead Connections
32q
ignore this procedure. (The yellow battery lead pro-
(53 mm)
have made and insulated all other connec-
Connect all wires, making sure that each connec-
vides continuous power to maintain a clock, memo-
tions.
tion is insulated and secure. Bundle all loose wires
75/32q
ry storage, or other function.)
and fasten them with tape so they will not fall down
(182 mm)
If your car has a radio or is pre-wired for one:
later. Now insert the stereo unit into the mounting
Ground
This unit can be installed in any dashboard having
With the ignition and headlights off, identify the car
collar.
Connect the black ground lead of the power con-
an opening as shown above. The dashboard should
battery lead by grounding one lead of the test bulb
nector to the metal car chassis.
Congratulations! After making a few final checks,
be 3⁄16z (4.75 mm)j7⁄32z (5.56 mm) thick in order to
to the chassis and checking the remaining exposed
you’re ready to enjoy your new auto stereo system.
be able to support the unit.
wires from the cut radio connector plug.
20
21
CQ-DFX501/DF401/DFX301U
CQ-DFX501/DF401/DFX301U


...

Эта инструкция также подходит к моделям:
Автомагнитолы - CQDFX301U (727.81 kb)
Автомагнитолы - CQDFX501U (727.81 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории