Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
When making electrical connections it is always recommended that the vehicle’s battery be disconnected from the electrical system before performingthe installation. 2. Carefully remove the trim panels covering the bolts that secure the radio into the dash cavity. Remove these bolts, and carefully pull the radio from the dash of the vehicle. This will provide access to the factory radio connectors where you will connect the Media Gateway harness. 3. Disconnect the factory 24-Pin and 16-Pin harnesses from the back of the radio. Disconnect the antenna from the radio. 4. When connecting the Satellite Radio tuner (SCC1 sold separartely), make the folllowing connections before connecting the PXAMG to the vehicle. Plug the black end of the 3 foot PXAMGSR cable (8-Pin mini-din to 8-Pin mini-din) into the second port (closest to the dipswitches) on the Media Gateway. Connect the gray end of this cable into the Satellite Radio tuner. 5. When connecting the auxiliary cable, plug the 8 pin mini-din into the port farthest from the dipswitches. Carefully run the auxiliary cable to the location where the auxiliary device will be stored. If you are using the RCA input it may be necessary to run the auxiliary device’s output cable to the PXAMG location. 6. Plug in the male connectors on the PGHFD1 harness into the 24-pin port and 16pin port on the back of the radio. Next, connect the factory 24-pin and 16-pin harness (if present) into the female connectors on the PGHFD1 harness. Be sure to make a firm connection but do not force it. If you are using the PGHFD1A harness, the 4 pin plug on this harness will connect to the 4-Pin plug on the PGHFD1 harness. The 12 pin plug on this harness will replace the current 12-pin harness connected to the LCD screen mounted above the radio. Disconnect the factory 12-Pin harness and do not reconnect. Plug the 12-Pin connector of the PGHFD1A harness into the LCD display. Again make a firm connection, but do not force. Plug the black micro-fit 24-pin connector on the PGHFD1 harness into the PXAMG Media Gateway box. 7. To complete the installation secure the Media Gateway (PXAMG) and Satellite Radio tuner (SCC1) into the cavity in the dash behind the radio. Be sure that the cables and interface modules are not near moving parts or sharp metal edges as they may damage the cables. To prevent rattling noises inside the dash, use zip ties, tape, or other fasteners to mount the interfaces securely. 8. With all connections made, reconnect the vehicle’s battery, insert the key into the ignition, and turn the vehicle on. Check for proper operation of the Media Gateway and Satellite Radio tuner before reinstalling the factory dash panels. 9. Note: The first time you access the Gateway, your radio may display “DEV INIT” while the device is initializing. After initially connecting the Gateway, please wait one minute then cycle the ignition off and on. Then access SAT mode again to begin normal gateway operation. 6.Sirius Satellite Radio Operation (Non-Navigation Radios) Press the AUX or Sirius button repeatedly (Must press SR icon & then use the SR123 icon on navigation radios) until “SIR-1” is displayed on the screen. *** NOTE When you press the AUX or SAT button, you will see the corresponding SAT mode (for example SAT 1), a slight delay, and then the current Gateway mode will be displayed (HD Radio/iPod/Sir1 - Sir 2 - Sir 3/Line In) Channel Up Press the ^ button to move up through the channels Channel Down Press the Ў button to move down through the channels Category Selection Press the Menu button until “SAT CAT” is displayed. Immediately press the ^ button to scroll through the categories. Stop when the category you want is displayed and it will automatically be selected by the PXAMG. Store Presets Press and hold the preset button on which you want to store the channel Recall Presets Press the button that corresponds with the channel you want to recall Changing Display Press the Text button to display artist and track information Sirius Satellite Radio Operation (Navigation Radios) Press the AUX or Sirius button repeatedly (Must press SR icon & then use the SR123 icon on navigation radios) until “SIR-1” is displayed on the screen. *** NOTE When you press the AUX or SAT button, you will see the corresponding SAT mode (for example SAT 1), a slight delay, and then the current Gateway mode will be displayed (HD Radio/iPod/Sir1 - Sir 2 - Sir 3/Line In) Channel Up Press the Tune ^ button to move up through the channels Channel Down Press the Tune Ў button to move down through the channels Category Selection Press Preset 6 to bring up the Categories menu. Press the ^ or Ў icons on the screen to scroll through the categories. Press the icon that represents the category you wish to select. Store Presets Press and hold the preset button on which you want to store the channel Recall Presets Press the button that corresponds with the channel you want to recall 7. Selecting AUX Input Press the AUX or Sirius but...