Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Adjusted equalizer curve settings are memorized in CUSTOM1 or CUSTOM2. 1 Press AUDIO to select the equalizer mode. Press AUDIO until EQ-LOW/EQ-MID/EQ-HIGH appears in the display. 2 Select the band you want to adjust with the 2/3. EQ-LOW (low)—EQ-MID (mid)—EQ-HIGH (high) 3 Press 5 or . to adjust the equalizer curve. Each press of 5 or . increases or decreases the equalizer curve respectively. • +6 – –6 is displayed as the equalizer curve is increased or decreased. • The actual range of the adjustments are different depending on which equalizer curve is selected. Note • If you make adjustments when a curve other than CUSTOM2 is selected, the newly adjusted curve will replace the previous CUSTOM1 curve. 32 En Section Audio Adjustments Equalizer curve fine adjustment Adjusting bass You can adjust the center frequency and the Q factor (curve characteristics) of each currently selected curve band (EQ-LOW/EQ-MID/EQHIGH). Level (dB) Q=2N Q=2W Frequency (Hz) Center frequency 1 Press AUDIO and hold until frequency and the Q factor (e.g., F-80 Q-1W) appears in the display. 2 Press AUDIO to select the desired band for adjustment. Press AUDIO repeatedly to switch between the following bands: EQ-LOW (low)—EQ-MID (mid)—EQ-HIGH (high) 3 Press 2/3 to select the desired frequency. Press 2 or 3 until the desired frequency appears in the display. LOW: 40—80—100—160 (Hz) MID: 200—500—1K—2K (Hz) HIGH: 3K—8K—10K—12K (Hz) 4 Press 5/. to select the desired Q factor. Press 5 or . until the desired Q factor appears in the display. 2N—1N—1W—2W Note • If you make adjustments when a curve other than CUSTOM2 is selected, CUSTOM1 curve is updated. You can adjust the cut-off frequency and the bass level. In FRT1 mode, bass adjustment affects only the rear output: front output cannot be adjusted. 1 Press AUDIO to select BASS. Press AUDIO until BASS appears in the display. 2 Select the desired frequency with 2/3. Press 2 or 3 until the desired frequency appears in the display. 40—63—100—160 (Hz) 3 Press 5 or . to adjust the bass level. Each press of 5 or . increases or decreases the bass level. +6 – –6 displayed as the level is increased or decreased. English En 33 Section Audio Adjustments Adjusting treble You can adjust the cut-off frequency and the Treble level. In FRT1 and FRT2 modes, treble adjustment affects only the front output: rear output cannot be adjusted. 1 Press AUDIO to select TRE. Press AUDIO until TRE appears in the display. 2 Select the desired frequency with 2/3. Press 2 or 3 until the desired frequency appears in the display. 2K—4K—6K—10K (Hz) 3 Press 5 or . to adjust the treble level. Each press of 5 or . increases or decreases the treble level. +6 – –6 displayed as the level is increased or decreased. Adjusting loudness Loudness compensates for deficiencies in the low- and high-sound ranges at low volume. 1 Press AUDIO to select LOUD. Press AUDIO until LOUD appears in the display. 2 Press 5 to turn loudness on. Loudness level (e.g., LOUD :MID) appears in the display. 3 Press 2 or 3 to select the level. Press 2 or 3 until the desired level appears in the display. LOW (low)—MID (mid)—HI (high) 4 Press . to turn loudness off. LOUD :OFF appears in the display. Using subwoofer output This unit is equipped with a subwoofer output which can be switched on or off. When a sub- woofer is connected to the rear output, first, switch the rear output setting to subwoofer, then turn the subwoofer output on. For more details, see Switching the rear output setting on page 37. 1 Press AUDIO to select SUB.W. When the rear output setting is subwoofer, you can select SUB.W. Press AUDIO until SUB.W appears in the display. 2 Press 5 to turn subwoofer output on. SUB.W :ON appears in the display. Subwoofer output is now on. 3 Press . to turn subwoofer output off. SUB.W :OFF appears in the display. Subwoofer output is now off. 34 En Section Audio Adjustments Adjusting subwoofer settings Adjusting source levels When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Press AUDIO to select the subwoofer setting. When the subwoofer output is on, you can select the subwoofer setting. Press AUDIO until 80Hz appears in the display. • If the subwoofer setting has been previously adjusted, the frequency of that previously selected will be displayed, such as 50Hz or 125Hz. 2 Press 2 or 3 to select cut-off frequency. Press 2 and 50Hz is displayed. Press 3 and 125Hz is displayed. Only frequencies lower than those in the selected range are output from the subwoofer. 3 Press 5 or . to adjust the output level of the subwoofer. Each press of 5 or . increases or decreases the level of the subwoofer (e.g., +6 to –6). Press 5 or . until you see the desired value displayed. SLA (Source level adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. • Settings are based on the volume level of the FM tuner, which remains unchanged. 1 Compare t...
Эта инструкция также подходит к моделям:Автомагнитолы - DEH-P4400RB (900.19 kb)