Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
5. information about the current track. • In radio mode, press and hold to store the • Press repeatedly to display available current radio station at channel No. 5. RDS information. • Press and hold to display the set clock. i • In radio mode, press to select the n AS/SOURCE preset radio station of No. 4. • Press repeatedly to select a source. • In radio mode, press and hold to store • In radio mode, press and hold to the current radio station at channel activate the automatic search of radio No. 4. stations. • For .wma and .mp3 tracks, press o repeatedly to select a play mode: play • Press repeatedly to select a preset all tracks randomly ([SHU ALL]), play sound equalizer. tracks in the current folder randomly • Press and hold to activate the setup of ([SHU FLD]), or play all tracks in the bass, treble, balance, and fader. storage device in sequence ([SHU OFF]). p • Press to turn on the system. j • Press and hold to turn off the system. • In radio mode, press to select the • Press to mute the speakers or release preset radio station of No. 3. them from mute status. • In radio mode, press and hold to store • Press to confirm an option. the current radio station at channel • Rotate to switch between menu No. 3. options. • For .wma and .mp3 tracks, press • Rotate to adjust the volume level. repeatedly to select a repeat mode: repeat the current track ([REP ONE]), q repeat all tracks in the current folder • For .wma and .mp3 tracks, press to ([RPT FLD]), or repeat all tracks in the select the next folder. storage device ([RPT ALL]). • Press and hold to activate the selection of listening zones. k • Press to select a tuner band. • In radio mode, press to select the preset radio station of No. 2. r / • In radio mode, press and hold to store • Tune to a radio station. the current radio station at channel • Press to skip to the previous/next No. 2. track. • For .wma and .mp3 tracks, press to • Press and hold to rewind a track or access the folder list. search fast forward. l s • In radio mode, press to select the • Press to enable or disable the preset radio station of No. 1. maximum volume. • In radio mode, press and hold to store the • Press and hold to enable or disable current radio station at channel No. 1. the DBB (dynamic bass boost) sound • For .wma and .mp3 tracks, press to effect. access the track list. EN t BAND • Press repeatedly to select a tuner band. u Slot for SD/SDHC card • Inser t an SD/SDHC card. v RESET • Press to reset the system to factor y default settings. EN 3 Install the car audio system Caution • Use the controls only as stated in this user manual. Always follow the instructions in this chapter in sequence. These instructions are for a typical installation. However, if your car has different requirements, make the adjustment accordingly. If you have any question regarding installation kits, consult your local retailer. Note • This system is designed for negative ground (ear th) 12V DC operation only. • Always install this system in the car dashboard. Other locations can be dangerous as the rear of the system heats up during use. • To avoid shor t-circuit: before you connect, make sure that the ignition is off. • Make sure that you connect the yellow and red power supply leads after all other leads are connected. • Make sure that all loose leads are insulated with electrical tape. • Make sure that the leads do not get caught under screws iron par ts that will move (e.g. seat rail). • Make sure that all ground (ear th) leads are run to a common ground (ear th) point. • Use only the supplied mounting hardware for a safe and secure installation. • Improper fuses can cause damage or fire. When you need to change the fuse, consult a professional. • When you connect other devices to this system, make sure that the rating of the car circuit is higher than the total fuse value of all the connected devices. • Never connect speaker wires to the metal body or chassis of the car. • Never connect speaker wires with stripes to one another. Connect wires Note • Make sure that all loose leads are insulated with electrical tape. • Consult a professional to connect wires as instructed below. 1 Check the car's wiring carefully and connect them to the the ISO male connectors. ISO male connectors Connect to 1 Green strip, black-Rear left speaker 2 White strip, black- edged white strip Front left speaker edged green strip 3 Gray strip, black-Front right speaker 4 Purple strip, black- edged purple strip Rear right speaker edged gray strip e Red strip Ignition key +12V DC when ON/ACC f Blue strip Motor/electric antenna relay control lead g White-edged blue Amplifier relay strip control lead h Black strip Ground EN 7 ISO male connectors Connect to ISO male connectors Connect to i Yellow strip To the +12V car batter y which is energized at all times 2 Connect the antenna and amplifier as illustrated, if applicable. REAR L R dcba Sockets on rear panel External sockets or connectors For ISO male As indicated above c...