Инструкция по эксплуатации Kenwood, модель KDC-X589
Производитель: KenwoodРазмер: 2.4 mbНазвание файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста
К этому устройству также есть другие инструкции:
Фрагмент инструкции
2 Enter Audio Control mode Press the [VOL] knob. 3 Select the Basic Audio item for adjustment Press the [VOL] knob. Each time the knob is pressed, the items that can be adjusted switch as shown below. 4 Adjust the Basic Audio item Turn the [VOL] knob. Adjustment Item Display Range Rear Volume *1 "R-VOL" 0 — 35 Subwoofer level*2,3,4 "SW L" –15 — +15 Bass level*5,6 "BAS L" –8 — +8 Middle level*5,6 "MID L" –8 — +8 Treble level*5,6 "TRE L" –8 — +8 Balance "BAL" Left 15 — Right 15 Fader*4 "FAD" Rear 15 — Front 15 Exit Audio Control mode • *1 You can control this item when "2ZON" of (page 11) is set to "ON". • *2 You can control this item when (page 25) is set to "SWPRE SW". (KDC-MP5028/ MP528 only) • *3 You can control this item when (page 11) is set to "SW ON". • *4 You can control this item when "2ZON" of (page 11) is set to "OFF". • *5 These items can be adjusted in detail by the following methods. (Function of the KDC-X589) • *6 Source tone memory: The set up value is put in the memory per source. (Detail Audio item is included) 5 Exit Audio Control mode Press any button. Press the button which is not [VOL] knob and [ATT]/ [ANG] button. Adjust the detail of Audio Control 1 Select the Audio item for adjustment By referring to the step 1 — 3 above, select the desired item to be set in detail from the items marked with *5. 2 Enter Detail adjustment mode of Audio Control Press the [VOL] knob for at least 1 second. 3 Select the Detail Audio item for adjustment Press the [VOL] knob. Each time the knob is pressed, the items that can be adjusted switch as shown below. 4 Adjust the Detail Audio item Turn the [VOL] knob. Bass level Adjustment Item Display Range Bass Center Frequency "BAS F" 40/50/60/70/80/100/ 120/150 Hz Bass Q Factor "BAS Q" 1.00/1.25/1.50/2.00 Bass Extend "B EX" OFF/ON Middle level Adjustment Item Display Range Middle Center Frequency "MID F" 0.5/1.0/1.5/2.0 kHz Middle Q Factor "MID Q" 1.0/2.0 Treble level Adjustment Item Display Range Treble Center Frequency "TRE" 10.0/12.5/15.0/17.5 kHz English | 11 5 Exit the Detail Audio Control mode Press the [VOL] knob for at least 1 second. • When the Bass Extend is set to ON, low frequency response is extended by 20%. • You can exit the Audio Control mode at anytime by pressing any button except for [VOL], [ATT] and [ANG] buttons. Audio Setup Setting the Sound system, such as Cross over Network. 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Setup mode Press the [VOL] knob for at least 1 second. 3 Select the Audio Setup item for adjustment Press the [VOL] knob. Each time the knob is pressed, the items that can be adjusted switch as shown below. 4 Setup the Audio item Turn the [VOL] knob. Adjustment Item Display Range Front High Pass Filter*2 "HPF" Through/40*./60*./80/100/ 120/ 150/180/220*. Hz Rear High Pass Filter*2 "HPR" Through/40*./60*./80/100/ 120/ 150/180/220*. Hz Low Pass Filter*1,2 "LPF" 50*./60/80/100*./120/ Through Hz Subwoofer Phase*1,2 "PHAS" Normal (0°)/ Reverse (180°) Volume offset "V-OFF" –8 — ±0 Loudness "LOUD" OFF/ON Dual Zone System*4 "2ZON" OFF/ON • Volume offset: Each source’s volume can be set as a difference from the basic volume. • Loudness: Compensating for low and high tones during low volume. When it's ON, "LOUD" indicator is ON. • *1 You can control this item when (page 25) is set to "SWPRE SW". (Function of the KDCMP5028/ MP528) • *1 You can control this item when (page 11) is set to "SW ON". • *2 You can control this item when "2ZON" of (page 11) is set to "OFF". • *. KDC-X589/MP5028 only. • *. The Dual Zone System can be used with the Auxiliary input sources shown below. - Internal auxiliary input (KDC-MP5028/MP528 only) - Option CA-C1AX (KDC-X589 only) • Dual Zone System Main source and sub source (Auxiliary input) output Front channel and Rear channel separately. - The channel of sub source is set up by (page 25). - Main source is selected by [SRC] button. - The volume of Front channel is adjusted by [VOL] knob. - The volume of Rear channel is adjusted by (page 10). - The Audio Control has no effect on sub source. 5 Exit Audio Setup mode Press [VOL] knob for at least 1 second. Subwoofer Output Turning the Subwoofer output ON or OFF. Hold down on [AM] of the Control knob for at least 1 second. Each time the button is pressed, Subwoofer output switches ON and OFF. When it’s ON, "SW ON" is displayed. • You can control this item when (page 25) is set to "SWPRE SW". (KDC-MP5028/MP528 only) • You can control this item when "2ZON" of (page 11) is set to "OFF". 12 | English General features Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "STANDBY" display. 2 Enter Speaker Setting mode Press the [VOL] knob. 3 Select the ...
Эта инструкция также подходит к моделям:
Автомагнитолы - KDC-MP5028 (2.4 mb)
Автомагнитолы - KDC-MP528 (2.4 mb)
)
Производитель: Kenwood
