Инструкция по эксплуатации Kenwood, модель KDC-W4537UY
Производитель: KenwoodРазмер: 2.1 mbНазвание файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста
К этому устройству также есть другие инструкции:
Фрагмент инструкции
• No output from the subwoofer. • Cannot set up the low pass filter. ^ • Preout is not set to subwoofer. . (page 26) • (page 9) is not set to On. ! Cannot set up the subwoofer phase. ^ Low pass filter is set to Through. . (page 9) ! • Cannot register a security code. • Cannot set up Display Illumination Control. ^ (page 29) is not turned off. ! Cannot set up the Power-off timer. ^ (page 24) is not set. ! Cannot play audio files. ^ (page 29) is set to "2". ! Cannot File select. ^ The Scan play or Random play function is enabled. What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on (page 33). Disc source ? The specified disc does not play, but another one plays instead. . The specified CD is quite dirty. . Clean the CD. . The disc is loaded in a different slot from that specified. . Eject the disc magazine and check the number for the specified disc. . The disc is severely scratched. . Try another disc instead. Audio file source ? The sound skips when an Audio file is being played. . The media is scratched or dirty. . Clean the media, referring to the CD cleaning of the section on (page 6). . The audio file is broken or not supported. . Damaged and unsupported files are skipped. . The recording condition is bad. . Record the media again or use another media. 36 | English USB device source ? The USB device is not detected. . The USB connector is disconnected. . Connect the connector of the USB device properly. ? The USB device does not play its audio files. . The USB connector is disconnected. . Connect the connector of the USB device properly. The messages shown below display your systems condition. EJECT: • No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. • No CD in the unit. NO DISC: No disc has been loaded in the disc magazine. TOC ERR: • No disc has been loaded in the disc magazine. • The CD is quite dirty. The CD is upsidedown. The CD is scratched a lot. READ ERR: • The number of files or folders which are stored in the connected USB device is above the limitation. • The file system of the connected USB device is broken. . Copy the files and folders for the USB device again referring to kenwood.com/usb/. If the error message is still displayed, initialize the USB device or use other USB devices. E-05: The disc is unreadable. BLANK: Nothing has been recorded on the MD. NO TRACK: No tracks are recorded on the MD, although it has a title. NO PANEL: The faceplate of the slave unit being connected to this unit has been removed. E-77: The unit is malfunctioning for some reason. . Press the reset button on the unit. If the "E-77" code does not disappear, consult your nearest service center. E-99: Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason. . Check the disc magazine. And then press the reset button on the unit. If the "E-99" code does not disappear, consult your nearest service center. LOAD: Discs are being exchanged in the Disc changer. READING: The unit is reading the data on the disc. HOLD: The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping all operation. . Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the disc will start playing again. English | 37 Troubleshooting Guide IN (Blink): PROTECT: NA FILE: COPY PRO: DEMO: NO DVICE: NA DVICE: NO MUSIC/E-15: USB ERR: iPod ERR: REMOVE: The CD player section is not operating properly. . Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center. The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. . Wire or insulate the speaker cable properly and press the reset button. If the "PROTECT" code does not disappear, consult your nearest service center. An Audio file is played with a format that this unit can’t support. . --- A copy-protected file is played. . --- The Demonstration mode has been selected. . The (page 29) is ON. Turn it OFF. The USB device is selected as a source although no USB device is connected. . Change the source to any source oth...
Эта инструкция также подходит к моделям:
Автомагнитолы - KDC-W4537U (2.1 mb)
Автомагнитолы - KDC-W4737U (2.1 mb)
Автомагнитолы - KDC-W4737UY (2.1 mb)
)
Производитель: Kenwood
