Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. — 8— Accessories Reattaching Faceplate: Hold the faceplate operation face faces toward you and press locks. The faceplate will and the unit will be operational. NOTE When there is difficulty in setting the faceplate, align the depression on the left side of the faceplate with the shaft of the unit, then lock. . Shaft Depression External view External view ......... Number ......... Number 3 1 ......... 2 ......... 2 4 2 .........1 ......... 1 2 CAUTION The use of any accessories except for those provided might in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. — 9— Installation Connections English The O-N switch should be set according to the Centre unit in use Centre unit as well as to the connected models. When the centre the O-N switch to operation, set the O-not available. The initial 1. To prevent a short circuit, remove disconnect the - battery. 2. Set the O-N switch of this unit to suit 3. Connect the speaker input cable to the wiring hernees of the centre unit. 4. Connect the control cable to the control connector. 5. Install the unit in your car. 6. Reconnect the - battery. 7. Press the reset button on the centre unit. N O N O – + – + FRONT • L FRONT • R R L KDC-D300 Control input White/Black White Gray/Black Gray White/BlackWhite Gray/BlackGray Speaker input cable( Accessory4) 2 CAUTION • Do not connect the changer control cable while the centre is turned ON. • Be sure to press the reset button after installation. • Whether the centre unit in use is compatible with the "N" operation or not can be identified by referring to its instruction manual (description of the disc control mode, etc.). • When this unit is connected with the KCA-S200 changer switching unit, set the O-N switch to "O". • Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. 2 CAUTION If the speaker input cable is not connected, or connected wrongly, the spectrum analyser will not be displayed. — 10 — Installation n Installation Accessory2 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and Metal mounting strap (commercially available) Firewall or metal support Self-tapping attach it in place. screw (commercially available) UPUP3 On cars where there is no compartment in the centre for installing a car audio unit: Use the spacer 3 to affix the centre unit sleeve and the sleeve attached to the main unit in such a way that they are correctly aligned both depthwise and horizontally. On cars lacking a centre compartment — 11 — Installation English ¦ Removing the hard rubber frame 1 Engage the catch locks on the lower level. Lower the frame and pull Catch Lock Accessory1 Removal tool 2 When the lower level is removed, remove the upper locations. — 12 — The frame can be removed from the top side in the same manner. Accessory2 Removing the Unit n Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 4 Pull the unit all the way out with your hands, being careful not to drop it. 5 Be careful to avoid injury from the catch pins on the removal tool. Catch facing up Refer to the section then remove the hard Remove the Hex-head . 8) on the back panel. Insert the two removal tools as shown. 3 2 1 NOTE 2 CAUTION Troubleshooting What might calling service, PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot No cable has been connected Connect the control cable to be selected. terminal on the unit. on the centre unit. No CD has been inserted. For centre units brought on to the onwards, it is not possible to switch a CD has already been inserted. No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set all the way Reset the fader or balance settings. side. 5 minutes have elapsed since the panel dropped open. When 5 minutes have elapsed since the panel dropped open, the disc will automatically stop playing. The spectrum analyser is not The speaker input cable is not connected. Refer to the "Connections" section, and connect the cable. displayed. The fader setting has been adjusted to the rear side. Adjust the fader control on the centre unit to the centre position. The analyser display level has been set too low. Adjust it to a higher level. The volume is too low. Raise the volume, or alternatively, adjust the analyser display level to a higher level. Nothing happens when the The computer chip in the unit is not functioning normally. Press ...