Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
2CAUTION 2WARNING ¦ Removing the transportation screws Transportation screws Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. After removing the transport screw, retain it carefully and attach it again before transporting the unit again. NOTE .........1 5 .........2 6 .........1 7 Accessories 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wiring harness wires in the following order: ground, battery, ignition. 4. Install the unit in your car. 5. Reconnect the - battery. 6. Press the reset button. Installation Procedure Installation Installation Angle adjustment The angle adjustment are to be set according auto changer. Set both position. If the switches are other malfunction may occur. Set the angle adjustment switches object. Change the switch step by step by detaching object at the end of each step. Angle adjustment switches 9090 0 45 90 0 45 Left side Right side Installation angle 0°~5° 40°~50° 85°~90° Angle adjustment switch position 90 0 45 90 0 45 90 0 45 • It is not possible to install at an angle of 40°~50° if only 1 is used. ¦ Installation of • Installation without 7 Display unit 5 Attach one velcro to the slanted-line of the the display units as shown above, and attach the other velcro to the parts where you wish to attach the display units. Then, put velcros together and install the display units. • Installation using the trim mount plate 7 Display unit 7 Pass the wire from the display unit through the hole on the trim mount plate and push fit the display unit into the trim mount plate until it locks. 2CAUTION • Be sure not to place the unit on such place as where it is exposed to direct sunlight and temperature eventually rises. It results in the deformation of the case. • Depending on the installing location, the display unit may not be able to receive the signals from the controller unit. Install them after confirming that the signals can be received. • Install the unit in such a way that it does not disturb driving. — 15 — — 16 — English Use the holes marked (¶) to install the unit. Use the holes marked (¶) to install the unit. ¦ Horizontal installation ¦ Vertical installation Bottom view Side view 90 0 45 90 0 45 90 0 45 90 0 45 90 0 45 90 45 0 2 3 . 4 1 2 3 1 . 4 Use the holes marked (¶) to install the unit. ¦ In case of hanging in the trunk ¦ Installation of FM modulator unit 90 0 45 90 0 45 90 0 45 Install the FM modulator unit beneath the front seat using Metal fixture and Bind head screw as shown in the above figure. Take sufficient care so that the wires are not caught under the seat. If they are caught, they may break. 2CAUTION . 3 . 4 2 3 1 6 Bottom view Side view Bottom view Side view Installation Connecting e rminals Connecting Display unit Control output Control input Changer connection wire 4 Output FM modulator unit FM/AM antenna input FM/AM antenna output Ground wire (Black) - (To car chassis) Car fuse box ACC Ignition key switch Antenna plug for automobile Car stereo with FM tuner Battery Battery wire + (Yellow) Ignition wire + (Red) CD auto - changer input NOTE 2WARNING To prevent fire when the ignition wire (Red) or battery wire (Yellow) is short-circuited by coming into contact with the vehicle chassis (ground), only connect the power supply after making the fuse box connections. Do not install an antenna of radio equipment or distribute the antenna wire near the changer output wire, for this could cause malfunction with this unit. 2CAUTION Be sure to press the reset button after installation. — 17 — English English What might just be the result Before calling service, possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the Reset button on the display unit (page 3). ? No sound or sound is low. . The radio volume is sets to the minimum level. . Turn the radio volume up. . The input/output wire or wiring harness is connected incorrectly. . Connect the input/output wire or wiring harness correctly. See "Connecting Wires to Terminals" (Page 17). ? Sound distortion. . The signal levels differ depending on sources. . Change the Modulation level / Dynamic control setting. (Page 11) ? Nothing appears on the display. . The control output of the display unit is not connected properly. . Connect the control output properly. Disc source ? CD play does not start. . CD auto-changer input is . Connect the CD auto-changer . Power button is not turned ON. . Turn the power button ON. ? The specified disc does not play, but . The specified CD is quite dirty. . Clean the CD. . The CD is upside-down...