Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
That information can be found on the page for External Disc Control in the section concerning switching to "N." • In the "N"-operation mode, the disc titles and track titles provided by the CD text function can be displayed. (only KDC-C712/C662) Installation n Accessories A . 1 B . 4 C . 4 D . 1 E . 1 F . 1 ' n Installation Procedure 1 Removing the transportation screws Remove all 3 transportation screws for protecting the internal mechanism before you start to install the unit. NOTE After removing the transport screw, retain it carefully and attach it again before transporting the unit again. 2 Angle adjustment switches • The angle adjustment switches on the both side of the unit are to be set according to the angle of installation of the CD auto changer. Set both of the two switches to the same position. If the switches are not set properly, sound skip or other malfunction may occur. • Set the angle adjustment switches with a coin or other flat object. • Change the switch step by step by detaching and reusing the object at the end of each step. Transportation screws 3 Cover the holes indicated by 3 with the dustproof seals E. (Bottom and sides) Use the holes marked l to install the unit. (See page 14) 2CAUTION Do not tighten the screw B too securely at the time of installation, but tighten it securely after having fixed the bracket A. 90 0 45 Angle adjustment switches 0 45 Installation angle 0°~5° 40°~50° 85°~90° Angle adjustment switch position 90 45 0 90 0 45 90 45 0 It is not possible to install at an angle of 40°~50° if only A is used. 7 n Horizontal installation Installation 90 0 45 A C B o4 Bottom view KDC-C662/C462 KDC-C712 90 0 45 90 0 45 90 0 45 90 0 45 90 0 45 3 3 3 3 3 3 n Vertical installation 90 45 0 A C B o4 Bottom view KDC-C662/C462 KDC-C712 90 0 45 3 390 0 45 90 0 45 90 0 45 90 0 45 3 3 3 3 n In case of hanging in the trunk 90 0 45 A C B o4 Bottom view KDC-C662/C462 KDC-C712 90 0 45 90 0 45 90 0 45 90 0 45 90 0 45 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 Troubleshooting Guide PROBLEM POSSIBLE CAUSE SOLUTION Sound skips due to vibration. • The unit is mounted at a slant. • Changer unit is mounted in an unstable place. • The angle adjustment switches are set improperly. • Mount the unit so that is level. • Mount the unit in a stable place. • Set the angle adjustment switches to the correct positions. The disc changer mode cannot be selected. The O-N selection switch of the disc changer is not set properly. Set the O-N selection switch to "O" position. When removing the CD changer, be sure to first eject a magazine then unplug the changer cord. Do not forget to attach the transport screws before transporting the CD changer. The CD changer may be damaged during transport if a magazine or CD is left inside it or the transport screws are not attached. Specifications Specifications subject to change without notice. Laser diode ..........................GaAlAs (l =780 nm) Operating voltage ....14.4 V (11 ~ 16 V allowable) Digital Filter ......................8 Time Over Sampling Current consumption ........0.8 A at Rated power D/A Converter ..............................................1 bit Dimensions (W . H . D) Spindle speed ....................500 ~ 200 rpm (CLV) (KDC-C712) ......................250 . 80 . 176 mm Wow & Flutter ..............Below Measurable Limit (KDC-C662/C462) ............250 . 64 . 176 mm Frequency Response (±1 dB)........5 Hz ~ 20 kHz Weight Total harmonic distortion (1 kHz)............0.005 % (KDC-C712)............................................2.0 k...
Эта инструкция также подходит к моделям:Автомагнитолы - KDC-C662 (270.88 kb)
Автомагнитолы - KDC-C712 (270.88 kb)