Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Front left output (White) Front right output (Red) Non-fading right output (Red) (KDC-7018 only) Power control wire (Blue/White) (KDC-7018/5018 only) Motor antenna control wire (Blue) (KDC-7018/5018 only) Dimmer control wire (Orange / White) When using the optional power amplifier, connect to its power control terminal. To car light control switch Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. External amplifier control wire (Pink / Black) To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function. Non-fading left output (White) (KDC-7018 only) TEL mute wire (Brown) (KDC-V7018R only) Connect to the terminal that is grounded when either the telephone rings or during conversation. Power control/Motor antenna control wire (Blue/White) (KDC-V7018R only) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. To KENWOOD disc changer/ DAB control input/ KPA-SD100/KPA-HD100/KPASS100 To connect these leads, refer to the relevant instruction manuals. NOTE Installation Installation Installation ¦ Installing in Japanese-Made Cars Accessory2 Metal mounting strap Self-tapping screw Firewall or metal support Accessory6 6 mm MAX. M5mm M5mm 6 mm MAX. T: Toyota cars N: Nissan cars T N N T T/N Accessory4...for Nissan car Accessory5 ...for Toyota car Refer to the section “Removing the hard rubber frame (P. 40)” and then remove the hard rubber frame. Mount the J-Car trim plate with the thick part at the bottom. Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. 3 2 1 4 5 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. (commercially Accessory8 available) J-Car Trim Plate (place thick part on NOTE bottom) Make sure that the unit is installed securely in place. If is unstable, it may malfunction (for example, the sound 2CAUTION skip). • During installation, do not use any screws except provided. The use of different screws might to the main unit. • Damage may occur if a screwdriver or similar excessive force during the installations. — 39 — English Installation Removing the hard rubber frame ¦ CatchLock Refer to the section “Theft deterrent faceplate (P. 10)” and then remove the faceplate. Engage the catch pins on the removal tool and remove the two locks on the upper level. Push upward the frame and pull it forward as shown in the figure. 2 1 Accessory3 Removal tool Accessory6 Removing the Unit ¦ Catch facing up Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. Remove the Hex-head screw with integral washer (M4.8) on the back panel. Insert the two removal tools deeply into the slots on each side, as shown. 3 2 1 Accessory3 Removal tool English Installation Removing the hard rubber frame ¦ CatchLock Refer to the section “Theft deterrent faceplate (P. 10)” and then remove the faceplate. Engage the catch pins on the removal tool and remove the two locks on the upper level. Push upward the frame and pull it forward as shown in the figure. 2 1 Accessory3 Removal tool Accessory6 Removing the Unit ¦ Catch facing up Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. Remove the Hex-head screw with integral washer (M4.8) on the back panel. Insert the two removal tools deeply into the slots on each side, as shown. 3 2 1 Accessory3 Removal tool 3 When the upper level is removed, remove the lower two tool toward the top, and locations. pull out the unit halfway whilst pressing towards the inside. 2CAUTION Be careful to avoid injury from the catch tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. NOTE The frame can be removed manner. — 40 — Installation Installation Locking the faceplate to the unit If you want to lock the faceplate to the unit so that it does not fall off, follow the directions below. 1 Refer to the function "Theft Deterrent Faceplate" (page 10) and remove the faceplate. 2 Insert the provided screw into the hole at the center of the bottom side of the faceplate which you have removed from the unit. Accessory7 3 Push back the bottom of the faceplate bracket unit it locks. 4 Refer to the section "Theft Deterrent Faceplate (page 10)" and then reattaching the faceplate. 2CAUTION Never insert the taptite screws (o2 . 4 mm) in any other screw holes than the one specified. If you insert it in another will contract and may cause damage to the mechanical inside the unit. — 41 — Troubleshooting Guide Troubleshooting Guide PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn on. The fuse has blown. After checking for short circuits in the wires, replace the fuse with one with the same rating. No sound can be heard, or the Attenuator is turned o...
Эта инструкция также подходит к моделям:Автомагнитолы - KDC-5018 (772.91 kb)
Автомагнитолы - KDC-V7018R (772.91 kb)