Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
• If your vehicle's ignition does not ignition wire is connected to a power voltage such as a battery wire, the power the ignition (i.e., it will not turn on and off ignition). If you want to link the unit's power connect the ignition wire to a power source on and off with the ignition key. • If the fuse blows, first make sure that the wires have a short circuit, then replace the old fuse with one with rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. — 30 — Connecting TEL MUTE P.CONT ANT.CONT. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 FRONTNONFADINGREAR Front left output (White) Front right output (Red) Rear right output (Red) / Non-fading right output (KDC-MV6521/M6021/6021 only) Rear left output (White)/ Non-fading lleft output (White) (KDC-MV6521/M6021/6021 only) Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Wiring harness (Accessory1) Connect to the terminal that is grounded when either the telephone rings or during conversation. Power control/ Motor antenna control wire (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. A–7 Pin (Red) A–4 Pin (Yellow) Connector B Fuse(10A) Connector A TEL mute wire (Brown) To connect the KENWOOD navigation system, consult your navigation manual. To KENWOOD disc changer/ DAB control input/ KPA-SD100/KPA-HD100/KPA-SS100 To External Display/ Steering remote To connect these leads, refer to the relevant instruction manuals. If no connections are made, do not let the cable come out from the tab. 27 Connecting TEL MUTE P.CONT ANT.CONT. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 FRONTNONFADINGREAR Front left output (White) Front right output (Red) Rear right output (Red) / Non-fading right output (KDC-MV6521/M6021/6021 only) Rear left output (White)/ Non-fading lleft output (White) (KDC-MV6521/M6021/6021 only) Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Antenna Conversion Adaptor (ISO–JASO) (Accessory3) Wiring harness (Accessory1) Connect to the terminal that is grounded when either the telephone rings or during conversation. Power control/ Motor antenna control wire (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. A–7 Pin (Red) A–4 Pin (Yellow) Connector B Fuse(10A) Connector A TEL mute wire (Brown) To connect the KENWOOD navigation system, consult your navigation manual. To KENWOOD disc changer/ DAB control input/ KPA-SD100/KPA-HD100/KPA-SS100 To External Display/ Steering remote To connect these leads, refer to the relevant instruction manuals. If no connections are made, do not let the cable come out from the tab. 27 Antenna Cord (ISO) Connector Function Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A–4 A–5 A–6 A–7 A–8 (KDC-MV6Yellow Blue/White Orange/White Red Black 521/M6021/602Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection 1 only) Speaker Connector B–1 Purple Rear Right ( + ) B–2 Purple/Black Rear Right ( – ) B–3 Gray Front Right ( + ) B–4 Gray/Black Front Right ( – ) B–5 White Front Left ( + ) B–6 White/Black Front Left ( – ) B–7 Green Rear Left ( + ) B–8 Green/Black Rear Left ( – ) (KDC-MV6521/M6021/6021 only) English English 2WARNING Connecting the ISO 31) The pin arrangement vehicle you drive. Make prevent damage to the unit. The default connection for the 1 below. If the ISO connector pins are set 2 or 3, make the connection as illustrated. 1 (Default setting) The A-7 pin (red) of the is linked with the ignition, and the A-4 pin the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) When the connection is made...
Эта инструкция также подходит к моделям:Автомагнитолы - KDC-5021 (1.64 mb)
Автомагнитолы - KDC-5021V (1.64 mb)
Автомагнитолы - KDC-6021 (1.64 mb)
Автомагнитолы - KDC-M6021 (1.64 mb)