Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 2CAUTION • If your car's ignition does not have ignition wires to a power source that with the ignition key. If you connect the ignition wire to a source with a constant voltage supply, as with battery wires, the battery may die. • If the console has a lid, make sure to install faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. — 13 — 13— 13 — —— Connecting Connecting P.CONT ANT. CONT. MUTE FRONT • L FRONT • R REAR • L REAR • R – + REAR L RFuse (10A) KENWOOD disc changer control Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box If no connections are made, do not let the 4 Front left output (Front right output (Red) To connect the Disc changer, consult your Disc changer manual. Power control wire (Blue/White) Motor antenna control wire (Blue) When using the optional power amplifier, connect to its power control terminal. Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. Not Used Do not let the wire come out from the tab. Purple Rear left output (White) Rear right output (Red) FM/AM antenna input To front left speaker To front right speaker To rear left speaker To rear right speaker Battery — 14 — 14— 14 — —— Installation Installation Installation Firewall or metal support Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installing in 1 Refer to the section and then remove the hard 2 Align the holes in the unit vehicle mounting bracket and screws. 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit (KDC-3026/KDC-2026/KDC-226/KDC-226B only) If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 Never insert the taptite screw (o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 15 — 15— 15 — —— Installation Installation ¦ Removing the 1 Engage the catch pins locks on the lower level. Lower the frame and pull Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner. ¦ Removing the 1 Refer to the section remove the hard rubber 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 16 — 16— 16 — —— Troubleshooting Troubleshooting General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same ...
Эта инструкция также подходит к моделям:Автомагнитолы - KDC-126 (501.94 kb)
Автомагнитолы - KDC-126S (501.94 kb)
Автомагнитолы - KDC-2026 (501.94 kb)
Автомагнитолы - KDC-226 (501.94 kb)