When recalling the memorized settings: Touching the screen displays a confirmation message. Touch Yes . To cancel recalling, touch No . KVT-839DVD When clearing the currently memorized settings: Touching the screen displays a confirmation message. Touch Yes . To cancel clearing, touch No . 4 Quit memorization/recalling of settings EXT SW Setup Setting up power specification of the external device for which the power is controlled from this unit. 1 Display the EXT SW SETUP screen Touch [Ext SW SETUP] in the SETUP Menu (page 62). 2 Perform EXT SW Setup Setting EXT SW Control 1 (EXT SW1) 2 Sets the power signal output mode. ( EXT SW1: Pulse, EXT SW2: Level) Pulse: Generates a single power signal pulse. Level: Continues output of high power signal. Sets to turn output on/off each time the button on the EXT SW Control screen is pressed. 3 Sets the Pulse signal output time. Outputs 500ms when "1" is set. Increases by 200ms with each step. Up to 100 steps can be set. 4 Returns to the original screen. Setting EXT SW Control 2 (EXT SW2) 1 2 3 4 The setup method is the same as "EXT SW1". 1 2 3 4 1Sets the name of the external device. See (page 53) for information on how to enter the name. English Audio Control Audio Control Audio Control Menu Displays the Audio Control menu to set the sound effect function of this unit. 1 Display the control screen Press several times until the control screen appears. 2 Display the Audio Control menu 3 Select the Audio Control item 1 1Switches to the selected Audio Control screen. Audio Control You can adjust the front/rear and right/left audio balance. 1 Display Audio Control Touch [Audio Control] in the Audio Control Menu (page 80). 2 Display the Audio Control screen 1 1 2 2 3 5 4 1 Adjusts the right and left volume balance. 2 Adjusts the front and rear volume balance. 3 Turns the Loudness control function On or Off. If turned "On", high and low tones are automatically enhanced during low volume. 4 Displays the present source information. The stream (Dolby Digital, dts, Linear PCM, MPEG or MP3/WMA), input channels (front or rear channels) are displayed. 5 Returns to the original screen. KVT-839DVD 6 7 8 9 10 6 Adjusts the bass boost of the B.M.S power amplifier (optional accessory). 7 Sets the center frequency of bass boost you have set for "AMP Bass". If you set the center frequency to "Low", it will be dropped approximately 20% to 30%. 8 Adjusts the subwoofer volume. 9 Adjusts the volume of the present source based on the difference level of original volume. p Returns to the original screen. . • If you have increased the volume first, then reduced the volume using the "Vol. Offset", the sound generated if you suddenly switch to another source may be extremely loud. • You may not set some models of power amp boost to "+18". See the catalog or instruction manual of power amplifier. Equalizer Control You can set up the equalizer. 1 Display Equalizer Control Touch [Equalizer] in the Audio Control Menu (page 80). 2 Display the Equalizer screen 1 2 3 4 1 Selects an equalizer curve type. You can select any of the following equalizer curves. • "Natural" • "Rock" • "Pops" • "Easy" • "Top40" • "Jazz" 2 Selects items to be adjusted for tone curve setup. If turned "Off", only Level can be setup for tone curves. 3 Displays the Tone curve setup screen. (page 82) 4 Returns to the original screen. English Audio Control Tone Setup You can set a Tone curve. 1 Display the Tone screen See (page 81). 2 Set the Tone 1 2 3 4 5 6 7 8 9 1 Bass adjustment items are displayed. 2 Middle adjustment items are displayed. 3 Treble adjustment items are displayed. 4 Bass DC Extend settings (Only when Bass is selected) If turned "On", it extends the bass center frequency to the low register by approximately 20%. 5 Tone curve becomes flat. 6 Sets the Center frequency. 7 Sets the level. 8 Sets the Q factor. (Only Bass and Middle can be set) 9 Returns to the original screen. Zone Control You can set the front and rear audio source. 1 Display Zone Control Touch [Zone Control] in the Audio Control Menu (page 80). 2 Set the Zone Control 1 3 5 2 3 4 1 Turns the Zone Function (that sets different source sounds for front and rear speakers) On or Off. 2 Switches the front and rear audio sources. (This button appears when the Zone function is On.) Use "Reverse" to change over the front and rear audio sources. 3 Sets the front and rear audio source separately. (This button appears when the Zone function is On.) KVT-839DVD . • When the rear speaker sound is switched, the audio source that is output at the AV OUTPUT terminal is also switched to the same source. However, if you have set the "Area" to "Reverse", the audio source that is output at the AV OUTPUT terminal is switched depending on the front sound source. 4 Adjusts the volume of the rear channel. (This button appears when the Zone function is On.) 5 Returns to the original screen. . • There are following limitations when zone func...
)
