Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
Insert the two removal tools deeply as shown. 3 2 1 NOTE 2CAUTION — 20 — Installation Screwing If you want to fasten does not fall off, screw o4 . 16 mm) in the hole shown below. Accessory7 2CAUTION Never insert the taptite screw ( o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, contact and may cause damage to the mechanical parts inside the unit. — 21 — Troubleshooting What might Before calling PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn on. The fuse has blown. After checking for short circuits fuse with one with the same No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set all Reset the fader or balance settings. side. The input/output wires or wiring harness are Reconnect the input/output wires or the wiring incorrectly. correctly. See the section on "Connecting Wires Terminals". The cassette tape is bad. Try playing another cassette tape. If works fine, the first tape was bad. The tape does not go in. / The car ignition was turned off during tape eject; or the Press the Eject button. No sound can be heard even tape was pulled out during loading, switching the mode to though the tape display is tape mode even though no tape is in. made. Nothing happens when the The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p. 4). buttons are pressed. The sound quality is poor or The tape head is dirty. Clean the tape head, referring to the section on "Cleaning distorted. the tape head" (see p. 4). One of the speaker wires is being pinched by a screw in Check the speaker wiring. the car. The speakers are not wired correctly. Reconnect the speaker wires so that each output terminal is connected to a different speaker. Radio reception is poor. The car antenna is not extended. Pull the antenna out all the way. The antenna control wire is not connected. Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". The memory is erased when The battery wire has not been connected to the proper Connect the wire correctly, referring to the section on the ignition is turned off. terminal. "Connecting Wires to Terminals". The ignition and battery wire are incorrectly connected. Connect the wire correctly, referring to the section on "Connecting Wires to Terminals". English — 22 — Troubleshooting External disc PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode No wire has been connected Connect the wire to the be selected. terminal on the unit. the unit. The specified disc does not The specified CD is quite dirty. Clean the CD. play, but another one plays instead. The CD is upside-down. Load the CD with the labeled side The disc is loaded in a different slot from Eject the disc magazine and check the specified disc. The disc is severely scratched. Try another disc instead. The sound skips. Something is touching the disc changer. Remove whatever is touching it. The CD is scratched or dirty. If skipping happens at the same place when the car is stopped, something with the CD is wrong. Clean the CD. The display shows that the The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p. 4) . changer is being played, but no sound can be heard. The specified track will not Random play or magazine random play has been selected. Turn off random play or magazine random play. play. If the following situations, consult your nearest service center: • Even though the disc changer is connected, the Disc Changer Mode is not on, Mode. • Even though no device (CA-C1AX) is connected, the AUX Mode is entered when — 23 — English Troubleshooting The following recommended No disc magazine ] Load the disc magazine No CD in the unit. ] Insert the CD. E-01 No disc has been loaded in the ] Load a disc into the disc magazine. E-02 E-04 No disc has been loaded in the disc ] Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. ] Clean the CD and load it correctly. E-10 Nothing has been recorded on the MD. ] The next MD will automatically be played. E-11 No tracks are recorded on the MD, although it has a title. ] The next MD will automatically be played. E-30 The faceplate of the slave unit being connected to this unit has ] Replace it. E-77 The unit is malfunctioning for some reason. ] Press the reset button on the unit. If the "E- 77" code does not disappear, E-99 Something is wrong with the disc magazine. Or the unit is malfunctioning for ] Check the disc magazine. And then press the reset button on the unit. If the "E- 99" code does not disappear, consult your nearest service center. E-0d The protective circuit in the unit activates when the temperature inside the automatic C (140° F), stopping all operation. ] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature C (140° F), the disc will start playing again. — 24 — Specifications S...
Эта инструкция также подходит к моделям:Автомагнитолы - KRC-308S (257.28 kb)
Автомагнитолы - KRC-38MR (257.28 kb)