Оценок - 5, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
on the car are — 14 — Connecting Wires to Terminals Connecting Wires to Terminals To connect the Disc changer, consult your Disc changer manual. FRONT • LFRONT • RREAR • LREAR • R P.CONT ANT CONT Fuse (10A) Wiring harness (Accessory1) 25 29 White/Black 32 Gray/Black 35 Green/Black 38 Purple/Black White 31 Gray 34 Green 37 Purple 40 Power control/Motor antenna control wire (Blue/White) Ignition wire (Red) 20 Battery wire (Yellow) 21 Ground wire (Black) · (To car chassis) 22 Ignition key switch Car fuse box (Main fuse) ACC 13 Car fuse box 14 If no connections are made, do not let the wire come out from the tab. 4 Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Rear left output (White) Rear right output (Red) FM/AM antenna input To front left speaker To front right speaker To rear left speaker To rear right speaker Battery — 15 — Installation Installation ¦ Installation Firewall or metal support Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (for example, the sound may Metal mounting strap (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installing in Japanese-Made Cars 1 Refer to the section "Removing the hard rubber frame" (page 17) and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 Never insert the taptite screw . 16 mm) in any other screw than the one specified. and may cause damage — 16 — Installation Installation Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. The frame can be removed from ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 17 — English English What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same cable to the ignition as the battery cable. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. ? There’s a source you can’t switch. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The faceplate does not open or close. . The faceplate is incorrectly attached. . Reattach the faceplate correctly, See the section on
Автомагнитолы - KRC-225 (265.68 kb)