Оценок - 3, средний балл: 4.7 ( )

Производитель: Panasonic Размер: 1.9 mb Название файла: CQR825EUC.PDF Язык инструкции:

Press “-/V or “N/* to shift the sound volume to the right or left speakers. or L 1 to 15 Balance Center • Press W or “N/* for more than a half second to change numeric levels on the display rapidly. Fader • Press SEL to select the FADER mode. Press W’ or “N/* to shift the sound volume to the front or rear speakers. or L 1 to 15 Balance Center Press “/V or “N/* for more than a half second to change numeric levels on the display rapidly. Note: When a control mode (BAS/TRE/BAL/FAd) is selected but no operation is made within 5 seconds (2 seconds at volume mode), the display will return to the normal operation (Radio, Cassette, etc) mode. In such a case, press SEL again to select the next control mode. CQ-R825/R805EUC Power and Sound Controls continued AUX Jack Selecting Auxiliary Source © Press AUX to select AUX Input mode. (D Connect the auxiliary equipment (an optional DCC player deck or any other appropriate equipment) to the AUX Jack. Canceling AUX Input mode Press AUX or MODE again while the AUX mode is operated, the mode will return to the previous mode. Or insert a cassette tape, and the mode will change to TAPE mode. Note: The AUX mode enables setting of VOL, BAS, and FAD, independently of other modes. Programmed Sound Memory Mode Selection A desired sound setting (except for VOL and ATT) can be memorized and recalled. Sound Memory Input • Press SDM to select the sound memory mode. • To preset a desired sound level, press the corresponding preset memory button (1 to 4) for more than 2 seconds in sound memory mode. • The preset memory buttons 5 and 6 are not valid for sound memory. Recall Sound Memory Call • When a desired preset memory button is pressed in sound memory mode, the corresponding sound setting is called. ■Preset number • The preset memory button 5 is recommended for setting. • The preset memory button 6 is used to release all sound settings. A-MIN1/2" LONG (12mm) B-MAX2/5" DIA. (10mm) C-MIN 1/8" DIA. (3.5mm) Caution: In order to insert the plug into the “AUX” Jack properly, make sure to use the correct size of the stereo plug shown on the left. CQ-R825/R805EUC To change to normal mode Press MODE or SDM to change to the normal mode. Note: When the sound memory mode is selected but no setting is made within 5 seconds, the mode will return to the normal mode. Level Meter When power is ON, the level of sound sources, such as radio and tape, is displayed. MONO I ==.' LOCAL -s!=5.-==.'=.\. Mil ECEUP L.:- „itufcàrâ ':Á: . W >№ 0*5 № №■№ № mVA » № № *MW M0 Hä/W WIU == MTL □□ B-SKIP REP RAND J=~== I I L-ch sound source level R-ch sound source level Note: The level meter indications do not change when VOL, BAL, or other control is turned. Iü) Radio Basics ,<0nll!^^-R825EUCi Change to the tuner mode Press MODE to switch the operation mode in the following order. TUNER ^ TAPE ^ CD Changer Control (When connecting CD Changer) t_* • Press AM to change to AM mode • Press FM to change to FM mode. • Press CST to change to Cassette mode. (When loaded a cassette) • Press CD*C to change to CD changer mode. (When connecting CD Changer) 7Y@rw Selecting a Band cOnly for CQ-R825EUC> Press BAND to select the bands in the following order. FM1 FM2 FM3 AM Press FM to select the bands in the following order. FM1 FM2 -► FM3 t_# “STEREO” indicator lights if the station is broadcasting in stereo. iigâii r M p i t~ ~ — * m c. i u c. * Manual Tuning Press “y\TUNE” or “V^TUNE” to move to a higher or lower frequency. Seek Tuning Press and hold “^TUNE” or “N/TUNE" for more than a half second, then release. The radio automatically stops on the next station. 10 CQ-R825/R805EUC Preset Station Setting Up to 24 stations can be preset in the station memory as follows; FM1 FM2 FM3 AM 6 stations 6 stations 6 stations 6 stations Manual Station Preset © Select a desired band. © Use manual or seek tuning to find a station that you want to program into memory. © Press and hold one of the station selector buttons 1 through 6 until the display blinks. The memory is now set for that button on the band you have selected. Repeat the process to set other stations for the FM1 to AM bands. -BUTTON NUMBER Note: You can change the memory setting by repeating the above procedure. Auto Station Preset Select a band and press APM. • The 6 strongest available stations will be automatically set in memory on preset buttons 1 through 6. • Once set, the preset stations are sequentially scanned for 5 seconds. • Press the appropriate preset button for the station you want to hear. MONO/LOCAL Selection • Much interference is reduced during a weak FM stereo broadcasts when MONO is ON.(Only for FM mo...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: