Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
I Press AM/FM when using a remote control. Manual Tuning Press TUNE A or TUNE V to move to a higher or lower frequency. ST indicator lights when FM stereo broadcast is received. Seek Tuning Press and hold TUNE A or TUNEV for more than 0.5 second, then release. The radio automatically stops at the next station. ST indicator lights when FM stereo broadcast is received. CQ-MRX777EUC Station Preset FM1, FM2, FM3 and AM can save maximum 6 stations each in their preset station memories. Manual Station Preset © Press BAND to select a desired band. Press AM/FM when using a remote control. (D Use manual or seek tuning to find a station that you would like to save into the memory. (D Press and hold one of the preset buttons 1 to 6 until the display blinks. Repeat the process to set other stations for the FM1 to AM bands. Preset number Note: You can change the memory setting by repeating the above procedure. Tuning in a Preset Station Press any of the buttons 1 to 6 to tune in the preset station. Auto Station Preset Select a band, press and hold BAND(APM) for more than 2 seconds. (APM: Auto Preset Memory) Press AM/FM for more than 2 seconds when using a remote control. • The 6 strongest available stations will be automatically set in memory on preset buttons 1 to 6. • Once set, the preset stations are sequentially scanned for 5 seconds each. • Press the appropriate preset button for the station you would like to listen to. Caution: For safety reasons, do not attempt to program while driving. CQ-MRX777EUC 13 Radio Basics (Continued) Switching Display Press DISP to change the display as follows. -► Regular Display (Band • Preset number * Frequency) I Clock Display i — Spectrum Analyzer Display MONO/LOCAL Selection • Much interference is reduced during a weak FM stereo broadcasts when MONO is on. (Only for FM mode) • Searching stops automatically at a strong signal only when LOCAL is on. 0 FM broadcasts Press and hold • (MONO/LOC) for more than 2 seconds to change the mode until reaching a desired mode, then release. MONO OFF LOCAL OFF MONO ON LOCAL OFF MONO OFF LOCAL ON MONO ON LOCAL ON •X- Press and hold MUTE for more than 2 seconds when using a remote control. (2) AM broadcasts Press and hold »(MONO/LOC) for more than 2 seconds to change the LOCAL mode as follows. LOCAL OFF LOCAL ON Press and hold MUTE for more than 2 seconds when using a remote control. 14 Compact Disc Player Basics CD Mode With no disc inserted (Standby Indicator off) © Press OPEN to open the front panel. (D Insert a disc with the label side up. (D Close the front panel by hand. The power is automatically switched on to start playing the CD. With a disc inserted (Standby Indicator lights.) Press SOURCE to change to CD. Play starts from first track. The standby indicator blinks. Press CD when using a remote control. CD Standby Indicator — ✓" \ Caution: • Never use a protect film, stabilizer and the like that are commercially available as CD accessories because they may cause faults or failures. • Close the control panel after the CD is completely pulled in. • Do not insert an MD into the CD slot to prevent any trouble. \__/ r Note: No operation can be performed except for CD eject when the front panel is open. Note: CDs of Special Shape Heart-shaped, octagonal, or other special-shaped CDs cannot be played. Do not use such CDs because they could cause technical trouble. CQ-MRX777EUC Compact Disc Player Basics (Continued) Stopping and Ejecting a Disc Open the front panel. (See page 11.) Press ± to stop CD play, and the disc will be quietly ejected from the CD slot. Power is automatically switched off after the CD is ejected. Caution: • When the front panel is open, do not force it down and do not put anything on it because these may result in damage to the unit. • Do not adjust the front panel angle, or open/close the front panel, if a CD or MD has not been completely inserted into, or removed from the CD or MD slot. Note: CD will not be ejected when the car engine switch is in the OFF position, or when the control panel is closed or removed. Track Selection • Press TRACKS once to go to the next track: • Press TRACK‘D* once to play from the beginning of the track you are listening to. Press twice to play the previous track. • Press repeatedly to skip the desired number of tracks. Track Search • Press and hold TRACK**** or TRACKS*’ for more than 0.5 second to activate reverse through or fast forward a track. • Release TRACKS or TRACK*>- to resume the regular CD play. Random Selection • Press 4(RANDOM). A random selection of music is played from all available tracks. • Press 4(RANDOM) again to cancel. RAND CQ-MRX777EUC Track Scan • Press 5(SCAN). The display will blink, and the first 10 seconds of each track on the disc will be played in sequence. • Press 5(SCAN) again to cancel. • Scan mode is also canceled when the CD has come to the beginning of the ...