Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOYMENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY. • Disconnect the cable from the negative battery terminal (see warning and caution below). • Remove Mounting Collar q from the main unit temporarily, which are already mounted at shipment.* Caution: Various settings that have been stored in the memory in other on-board equipment (vehicle navigation etc.) may be lost if the battery terminals are disconnected. Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals. After completing installation of the main unit, set the equipment again according to the record. • Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. . Dashboard Installation Installation Opening This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 3/16” (4.75 mm) – 7/32” (5.56 mm) thick in order to be able to support the unit. No. Item Diagram q Mounting Collar* 1 w Plain washer (5mmo) 2 e Spring Washer (5mmo) 2 r Hex. Nut (5mmo) 2 t Rear Support Strap 1 y Hex. Bolt (5mmo . 25 mm) 1 u Toothed Lock Washer (5mmo) 1 i Removal Tool (U-shaped) 2 CQ-5301U 21 Mounting bolt (5 mmo) ..Mounting collar Rear support bracket (provided on the vehicle)Rubber cushion (option) (a) Using the rear support strap t (b) Using the rubber cushion (option) Installation (Continued) Cautions: • We strongly recommend that you wear gloves for installation work to protect yourself from injuries. • When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. First complete the electrical connections, and then check them for correctness.(apage 24) The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model. 1 2 3 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. Establish the rear connection of the unit. After fixing Power Connector, fix the rear of the unit to the vehicle body by either method (a) or (b) shown in the previous page. After installation reconnect the negative (–) battery terminal. The tabs to be bent vary depending on the vehicle. To securely install the unit, fully bend a number of the tabs so that there is no rattling. Example: Tab q Mounting Collar Mounting Holes Mounting Bolt Power Connector Mounting springs (C) Engage the Mounting mounting holes of the Mounting Hole Springs (C) in the Mounting Collar q firmly. Mounting Spring CQ-5301U To Remove the Unit from the vehicle's dashboard Insert each Removal Tool i and pull. i Removal Tool (U-shaped) Note: Do not lose Removal Tools. They will be needed to remove the unit from the vehicle's dashboard. CQ-5301U Electrical Connections Cautions: • This wiring information is for experienced technical individual, for safety reason, please your dealer wire this connection. • This product is designed to operate with a 12 V DC, negative ground battery system. • To prevent damage to the unit, be sure to follow the connection diagram below. • Do not insert the power connector into the unit until the wiring is completed. • Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and keep cable terminals free from touching any metal parts. • Remember, if your vehicle has a drive computer or a navigation computer, the data of its memory maybe erased when the battery terminals are disconnected. . Wiring Diagram CQ-5301U Specifications . General Power Supply: 12 V DC (11 V-16 V) test Voltage 14.4 V, Negative ground Current consumption: Less than 2.5 A (CD mode, 0.5 W 4-speaker) Maximum Power Output: 37 W . 4 channels at 400 Hz, Volume Control maximum Tone adjustment range: Bass: ± 12 dB at 100 Hz Treble: ± 12 dB at 10 kHz Power Output: 18 W per channel into 4 ohms, 40 to 30 000 Hz at 3 % THD Suitable Speaker Impedance: 4-8 . Dimensions (W H D): 7" 1-15/16" 5-7/8" (178 50 150 mm) Weight: 2.8 lbs. (1.3kg) . FM Stereo Radio Frequency Range: 87.9-107.9 MHz Useable Sensitivity: 12 dBf. (1.1 .V/ 75 ., S/N 30 dB) 50 dB Quieting Sensitivity: 17 dBf. (1.8 .V/ 75 .) Frequency Response: 30-15 000 Hz ±3 dB Alternate Channel Selectivity: 75 dB Stereo Separation: 35 dB at 1 kHz Signal/Noise Ratio: 70 dB (Mono) . AM Radio Frequency range: 530 kHz – 1 710 kHz Usable sensitivity: 28 dB/.V (25 .V, S/N 20 dB) . Weather Band Radio Frequency range: 162.40 – 162.55 MHz Usable sensitivity: 3 dB/.V (S/N 20 dB) Signal/Noise Ratio (40 dB/.V): 50 dB . CD Player Sampling Frequency: 32 times oversampling DA Converter: MASH•1 bit/4 DAC System Error Correction System: Panasonic Super Decoding Algorithm Pick-Up Type: 1-beam Light Source: Semiconductor laser Wavalength: 790 nm Frequency Response: 20 - 20,000 Hz (±1 dB) Signal to Noise Ratio: 85 dB Total Harmonic Distor...