Оценок - 5, средний балл: 3.8 ( )

Производитель: Bazooka Размер: 3.76 mb Название файла: Язык инструкции:

Run signal wires away from electrical wires to avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise). Please note that when making these connections the signal inputs correspond with the speaker outputs. For example: If you connect the radios front right RCA to “CH 1” .......then speaker output “CH 1” will operate the front right speaker. INPUT CH1 CH2 CH4 CH3 FILTER LOW FLAT HIGH FILTER LOW FLAT HIGH LEVEL MIN MAX LEVEL MIN MAX POWER PROTECT POWER 0dB X-OVER 40Hz 130Hz REMOTE OUTPUT INPUT LEVEL L R MIN MAX POWER PROTECT LEVEL INPUT R L MIN MAX FILTER LOW FLAT HIGH CSA50.2 SIGNAL CONNECTIONS L R CSA50.4 & CSA200.3 SIGNAL CONNECTIONS FRONT REAR R L L R CSA150.1 & CSA300.1 SIGNAL CONNECTIONS Optional full range line out connection to additional amplifiers in the system. R L L R Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response. When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). SPEAKER CONNECTIONS CSA50.4 SPEAKER CONNECTIONS SPEAKER FUSE + BRIDGED - POWER +12V REM GND L + L - R+ R - + CH3 - + CH4 - + BRIDGED - FUSE POWER SPEAKER GND REM +12V + CH1 - + CH2 - 4 Ohm Speakers (2 Ohm Minimum) 4 Ohm Speakers (2 Ohm Minimum) CSA50.2 SPEAKER CONNECTIONS 4 Ohm Speakers (2 Ohm Minimum) + - + - 9 FUSE +12V REM GND SPEAKER + - CSA150.1 & CSA300.1 SPEAKER CONNECTIONS 4 Ohm Speaker (2 Ohm Minimum) CSA200.3 SPEAKER CONNECTIONS FUSE SPEAKER POWER GND REM +12V + + + + - - - - CH3 CH4 BRIDGED CH1 CH2 4 Ohm Speaker (2 Ohm Minimum) 4 Ohm Speaker (2 Ohm Minimum) 4 Ohm Speaker (2 Ohm Minimum) + - + - + - 10 CSA50.2 BRIDGED SPEAKER CONNECTIONS CSA200.3 BRIDGED SPEAKER CONNECTIONS CSA50.4 BRIDGED SPEAKER CONNECTIONS SPEAKER CONNECTIONS (BRIDGED) The EL amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. 11 FUSE SPEAKER POWER GND REM +12V + + + + - - - - CH3 CH4 BRIDGED CH1 CH2 4 Ohm Speaker 4 Ohm Speaker + - + - + CH3 - + CH4 - + BRIDGED - FUSE POWER SPEAKER GND REM +12V + CH1 - + CH2 - 4 Ohm Speakers SPEAKER + BRIDGED - POWER +12V REM GND L + L - R+ R - + - 4 Ohm Speaker **CAUTION! In the bridged mode, the amplifier must see a 4 Ohm load or higher. Any lower than 4 Ohms will cause the amplifier to overheat and possibly cause CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier. SPEAKER CONNECTIONS (TRI-MODE) 12 The amplifier is capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple speakers to achieve a lower impedance and higher power, it is strongly recommended that you seek professional advice from your BAZOOKAd retailer before attempting to make these connections. Please Note: In the Tri-mode configuration, the amplifier’s built-in crossover must be set to the ”FLAT” position so the speakers receive full range output. SPEAKER FUSE + BRIDGED - POWER +12V REM GND L + L - R+ R - NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D 100 F - + 100 F + - - 4 mH Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) REMOTE BASS CONTROL MODULE (CSA300.1 OPTIONAL) Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting location, you will need to run the control wire from the remote to the amplifier. To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise), run the cable from the remote to the amplifier away from the car's e...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: