Оценок - 3, средний балл: 3.3
(
)
)
|
Фото и характеристики Alpine CDA-9886R |
Фрагмент инструкции
This device can only display single-byte alphanumeric characters (up to 30 for ID3 tags and up to 15 for WMA tags) and the underscore. For non-supported characters, the display is blank. The tag information may not be correctly displayed, depending on the contents. Do not make a file’s playback time more than 1 hour. Playing back MP3/WMA/AAC MP3/WMA/AAC files are prepared, then written to a CD-R, CD-RW using CD-R writing software or stored to a USB memory. A disc can hold up to 510 files/folders (including Root Folders), and the maximum number of folders is 255. This unit can recognise at least 100 folders (including root folder) and 100 files per folder stored in USB memory. Playback may not be performed if a disc or USB memory exceeds the limitations described above. Media supported The media that this device can play back are CD-ROMs, CD-Rs, and CD-RWs. This device also can play back USB memory media. Corresponding File Systems This device supports discs formatted with ISO9660 Level 1 or Level 2. Under the ISO9660 standard, there are some restrictions to remember. The maximum nested folder depth is 8 (including the root directory). The number of characters for a folder/file name is limited. Valid characters for folder/file names are letters A-Z (all caps), numbers 0-9, and ‘_’ (underscore). This device can play back discs in Joliet, Romeo, etc., and other standards that conform to ISO9660. However, sometimes the file names, folder names, etc., are not displayed correctly. This device also supports FAT 12/16/32 for USB memory device. Formats supported This device supports CD-ROM XA, Mixed Mode CD, Enhanced CD (CD-Extra) and Multi-Session. This device cannot correctly play back discs recorded with Track At Once or packet writing. Order of files Files are played back in the order that the writing software writes them to the disc. Therefore, the playback order may not be what is expected. Verify the writing order in the software’s documentation. The playback order of the folders and files is as follows. Root folderFolderMP3/WMA/AAC File *The folder No./ folder Name will not be displayed if no file is contained in the folder. Bit rate This is the “sound” compression rate specified for encoding. The higher the bit rate, the higher the sound quality, but also the larger the files. Sampling rate This value shows how many times per second the data is sampled (recorded). For example, music CDs use a sampling rate of 44.1 kHz, so the sound is sampled (recorded) 44,100 times per second. The higher the sampling rate, the higher the sound quality, but also the larger the volume of data. Encoding Converting music CDs, WAVE (AIFF) files, and other sound files into the specified audio compression format. Tag Song information such as track titles, artist names, album names, etc., written into MP3/WMA/AAC files. Root folder The root folder (or root directory) is found at the top of the file system. The root folder contains all folders and files. It is created automatically for all burned discs. Sound Setting /ENTBAND/TARotary encoder (AUDIO·LOUD)SOURCE/ SOUND SETUP/ESC Adjusting Subwoofer Level/Bass Level/ Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/ Auto Volume/Defeat 1Press Rotary encoder (AUDIO) repeatedly to choose the desired mode. Each press changes the mode as follows: SUBWOOFER*1 BASS TREBLE BALANCE FADER AUTO VOLUME*2 DEFEAT VOLUME SUBWOOFER Subwoofer level: 0 ~ +15 Bass level: –7 ~ +7 Treble level: –7 ~ +7 Balance: L15 ~ R15 Fader: R15 ~ F15 Auto Volume: OFF/LOW/MIDDLE/HIGH Defeat: ON/OFF Volume: 0 ~ 35 •If no operation is performed for 5 seconds after selecting the SUBWOOFER, BASS, TREBLE, BALANCE, FADER, AUTO VOLUME or DEFEAT mode, the unit automatically returns to normal mode. *1When the subwoofer mode is set to OFF, its level cannot be adjusted, refer to “Turning Subwoofer ON/OFF” (page 18). *2By setting AUTO VOLUME, the unit can automatically adjust volume to a proper level according to engine/road noise, etc. There are three volume correction degrees: LOW, MIDDLE and HIGH. 2Turn the Rotary encoder until the desired sound is obtained in each mode. By setting Defeat ON, previously adjusted settings of BASS and TREBLE will return to the factory defaults. •Depending on the connected devices, some functions and display indications do not work. Setting the Subwoofer Level You can change the Subwoofer Level to create your own tonal preference. 1Press SOUND SETUP to activate the Sound Setting mode. 2Turn the Rotary encoder to select the SUBW. Level Adjustment mode, and then press /ENT. SUBW. Level*3 Bass*4 Treble*4 HPF*4 Black Out SUBW. Level 3Turn the Rotary encoder to select the desired subwoofer level (0~+15). •If no operation is performed for 15 seconds, the unit will return to normal mode automatically. *3When the subwoofer mode is set to OFF, its level cannot be adjusted, refer to “Turning Subwoofer ON/OFF” (page 18). The adjustment can also be made by pressing Rotary encoder ...