Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
1 Press SEL repeatedly to select the mode to be adjusted. Pressing SEL cycles through the modes. The selected mode’s indicator flashes. 2 Turn AUDIO CONTROL to increase/decrease the level or to select on/off for the selected mode. Note Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state. Aligning the source levels (Source Level Adjuster) Volume may vary each time you change the source mode. In this case, you can align each source mode’s volume to almost the same level. 1 PressSRC or BAND repeatedly to select the desired mode. 2 Press DISP while pressing SEL. “LA 0” appears in the display. 3 Turn AUDIO CONTROL to adjust the level. Note Adjust the level within 5 seconds, or the selected mode will be canceled. Restoring the factory settings 1 Turn off the unit. 2 Press and hold DISP until “LA --” appears in the display. Note You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels. Muting button beep sounds 1 Turn off the unit. 2 Press and hold SEL until “bEEP” appears in the display. 3 Turn AUDIO CONTROL to select on (level indicators appear) or off (level indicators disappear). 4 Press SEL. Setting the clock 1 Press and hold DISP until the clock indicator flashes in the display. 2 Press i (to set hour) or k(to set minute), and then turn AUDIO CONTROL. 3 Press DISP. Displaying the clock 1 Press DISP. To return to the former display, press DISP again. RADIO OPERATION Tuning in to a station (Seek/Manual Tuning) LO i/k BAND Stereo indicator Local indicator Band indicator Frequency indication 1 Press BAND repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). 2* Press i(to move to higher frequencies) or k(to move to lower frequencies) to tune in to a station. “ST” appears in the display when an FM station is broadcasting in stereo, and receiving conditions are good. *Seek Tuning and Manual Tuning • Press and hold ior kuntil seek Tuning starts. The unit locates a station automatically (Seek Tuning). • Press i or k repeatedly to search for a desired station while increasing or decreasing the frequency step by step (Manual Tuning). To stop Seek Tuning, press ior kagain. 3 33 ENGLISH ENGLISHENGLISH Monaural mode When signals become weak, or reception becomes poor, the unit automatically switches to Monaural mode to reduce noise. Local mode Local mode allows you to tune in only to strong stations during Seek Tuning. 1 Press LO before you start seek tuning. “LO” appears in the display. To return to Distant mode, press LO again. “LO” disappears and the unit tunes in to all receivable stations. Using preset stations You must preset stations before you can tune in a station using preset station number buttons. i/kPS/A.ME BAND Preset station buttons 1 to 6 Preset station number Presetting stations automatically (Auto Memory) 1 Press BAND repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). 2 Press and hold PS/A.ME until automatic presetting starts. The unit automatically stores up to 6 stations for each band. After completion of automatic presetting, the unit tunes in to the station stored on preset station button 1. To cancel automatic presetting,press PS/A.MEagain. Checking the preset stations (Preset Scan) 1 Press PS/A.ME briefly. Each preset station will be tuned in for 5 seconds in order. To cancel Preset Scan, press PS/A.ME again or any preset station button. Presetting stations manually (Manual Memory) 1 Press BAND repeatedly to select the desired band (FM1, FM2, FM3, AM1, or AM2). 2 Press ior kto tune in to a desired station (see “Tuning in to a station” as well for another tuning method). 3 Press and hold the desired preset station button until the unit beeps. Note A newly preset station replaces the station on the same band that was previously stored on that preset station button. Tuning in to a preset station 1 Press BAND repeatedly to select the desired band (FM1, FM2, FM3, AM1 or AM2). 2 Press the preset station button on which the desired station is stored. Active tuning reception control (ATRC) The unit automatically suppresses FM noise caused by vehicle movement, and maintains sound quality. CD PLAYER OPERATION Playing a CD You can play CDs, CD-Rs and CD-RWs using the procedure described below. SRC z r/tINT RNDM REP 1 1 Insert a CD. “CD” appears in the display. CD play starts. If a CD is already inserted, press SRC repeatedly to select CD play mode. In normal play, when the last track finishes, the unit returns to the first track and continues to play. ENGLISH ENGLISHENGLISH 4 44 Labeled-side up Track number CD indicator Elapsed playing time To Press Eject a CD z Skip to the next track t Go back to the beginning r of the current track Each extra press skips backward one extra track Locate a specific point in Press and hold ror a track tuntil you find the point. Note • When you play a CD that is already inserted, CD play starts at the point where it stopped the previous t...