Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
• To unbuckle: Press red button, pull tongue out of opening and lift shield 18 over top of car seat. 5 Recline / Upright Positions (fig. c:): Rear-facing - MUST use Recline position. Forward-facing - MUST use Upright position • Upright Position: Rotate stand out and push into car seat. • Recline Position: Pull stand out and rotate into car seat. 5-Point Crotch Strap Adjustment (fig. d): MUST be in opening closest to but not under child. • From bottom of car seat, pull crotch strap clip out and remove clip from crotch strap loop. • From top of car seat, pull crotch strap out and thread through desired slot. Make sure red button is facing away from child. • From bottom of car seat, re-attach clip to crotch strap loop exactly as shown. 19 (fig. a) (fig. b) PUSH (fig. c) 2 3 2 3 (fig. d) 4 Upright Recline OPERATIONS and ADJUSTMENTS (continued) Clip 5-Point Models Overhead Shield Models 4 Adjuster Bar 5 Harness Lock OPERATIONS and ADJUSTMENTS (continued) Changing Harness Strap Slots: The harness straps must go into the slots even with or just above the shoulders. A To adjust harness straps: Remove straps from harness plate and adjuster bar (fig. a). 7 Overhead Shield Adjustment (fig. f): • To adjust: Press both buttons down and move shield to desired position closest to child. Release buttons to lock shield into place. Check by pulling out on shield. NOTE: Shield does not need to contact child when in closest position; harness system restrains child. B Pull strap ends through slots and reinsert them in the correct slots (fig. b). C Reassemble straps onto adjuster bar exactly as shown (fig. c). D Push adjuster bar down (fig. d). E Rotate lock down (fig. e). NOTE: • Make sure both harness straps are securely attached within Harness Plate and Adjuster bar and locked into place with Harness Lock. • Make sure straps are NOT twisted. OPERATIONS and ADJUSTMENTS (continued) AllModels (fig. f) Tether Harness Plate Adjuster Bar (fig. a) Harness Lock (fig. e) (fig. b) (fig. c) (fig. d) OPERATIONS and ADJUSTMENTS (continued) LATCH Belt Routing:8 LATCH belt MUST be routed through the proper openings depending on direction of car seat use. A Route LATCH belt through Rear-facing openings for: • LATCH Rear-facing use. Rear-facing opening B Route LATCH belt through Forward-facing (fig. h) openings for: • LATCH Forward-facing use. Rotate LATCH belt so that the belt routes through the proper openings (fig. h and fig. i). Belts must remain flat and not twisted. (fig. i) Forward-facing opening OPERATIONS and ADJUSTMENTS (continued) 9 Removing LATCH from Vehicle Anchor Points: A Tilt metal tab of adjuster to release tension (fig. j). HINT: Press down on car seat compressing vehicle seat cushion to reduce tension on lower anchorage belt. B Press and hold LATCH release hinge. (lower hinge) (fig. k). C Push connector in, lift connector up and pull out (away from anchor point) (fig. l). Repeat step A, B and C for other connector. (fig. j) (fig. k) (fig. l) OPERATIONS and ADJUSTMENTS (continued) 10 LATCH storage: • Locate LATCH storage openings on top of car seat (fig. m). • Fasten LATCH into storage opening as shown. (fig. n) LATCH storage • Reinstall seat pad over top of carseat. opening Repeat for other connector. (fig. m) (fig. n) VEHICLE SEAT BELTS WARNING Not all vehicle seat belts can be used with a car seat. The car seat must be held securely at all times by a lap belt (or lap belt portion of a lap/shoulder belt) that will not change length while driving. To provide the most secure installation of the car seat: • Read the vehicle owner’s manual regarding car seat installation and seat belt use with car seat. • Follow all instruction labels on vehicle seat belt and car seat. If car seat is not held securely after following instructions in this manual, vehicle seat belt labels, and vehicle owner’s manual: • Move car seat to another seating location and try again, or • Contact vehicle dealer for possible seat belt modification parts. VEHICLE SEAT BELTS (continued) Vehicle seat belts located forward of seat crease may not securely hold car seat. Check vehicle owner’s manual or see vehicle dealer for car seat installation requirements. • If approved for use with car seat, install car seat and check for secure installation by pulling car seat front to back. If car seat slides forward, DO NOT use these seat belts. Seat Crease Seat Crease Belts Forward of Seat Crease VEHICLE SEAT BELTS (continued) . Lap Belts - Manually Adjustable The locking latch plate on some seat belts may slip and loosen after being buckled on car seat if positioned at a certain angle. If this happens, flip latch plate over (fig. a) and re-buckle. Test installation again to see if this works. If not, move car seat to another seating position. . Lap Belts - With Retractor Flip Lap belts with retractors may or may not hold (fig. a) a car seat securely. Follow these steps to determine if you have a retractor system that will hold car seat securely: a. Pull belt all the ...
Эта инструкция также подходит к моделям:Автокресла - 44164 (1.8 mb)