Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
a. Extend vehicle lap belt all the out the way out and buckle vehicle belt. b. Place center section of lap belt flat on vehicle seat as shown in fig. c. Check that vehicle lap belt is not twisted and lays flat across seat. Route vehicle lap belt through base. a. Center base on the center section of lap belt. (fig. c) CenterSectionOfLapBelt b. On side of base lift lap belt up and hook over blue belt guide 2 1 , placing lap belt into belt slot on blue belt guide (fig. d). Check that lap belt is not twisted. c. Repeat step b for opposite side of base. NOTE: When installing with a lap and shoulder belt, route only the lap belt through the base, DO NOT route the shoulder belt through base. Tighten vehicle belt to secure the base. Press down in center of base to depress the vehicle cushion while tightening vehicle belt (fig. e & f). -When using a vehicle lap and shoulder belt, after tightening lap portion of the belt, place shoulder belt into slot in corner of base and allow shoulder belt to rest against vehicle seat back (fig. g). Check for secure installation. Pull base front to back and (fig. e) Lap Belt (fig. f) Lap and left to right to check for secure installation (fig. h). Vehicle Shoulder Belt lap belt MUST stay tight. If the vehicle lap belt does not stay tight or base cannot be securely installed, see vehicle owner’s manual, “Vehicle Seat Belts” section or move to a different seating location. Attach car seat to base. Lift car seat to ensure it is properly attached to the base (see “Attachment Of Car Seat To Base” section). Recheck recline of car seat. Adjust if necessary (fig. g) (fig. h) (see step 4). 30 (fig.d) 12 31 Securing Infant Car Seat Without Base: •Notallvehicleseatbeltscanbeusedwithacarseat.Readvehicleowner’smanualand“VehicleSeatBelts”sectioninthismanual. WARNINGDEATHorSERIOUSINJURYcanoccur Installation with Lap Belt Only: 4123 Refer to vehicle owner’s manual to identify the seating locations which can be used with a car seat. Check for specific instructions for car seat use. After selecting a seating location, if vehicle seat back is adjustable, adjust vehicle seat back into most upright position. Place car seat rear-facing on vehicle seat. Thread vehicle lap belt through vehicle lap belt guides on car seat (fig. a) and buckle vehicle belt. Be sure vehicle lap belt is not twisted. (fig.a) 65 Press down firmly on car seat to compress vehicle seat cushion while tightening vehicle lap belt (fig. b). Adjust recline using the recline indicator on the side of car seat (fig. c). Line on recline indicator must be in green striped zone. If line is not in green striped zone, place a tightly rolled up towel, blanket or firm foam (pool noodle) under end of car seat contacting vehicle seat back. If car seat can not be adjusted to locate the line in the green striped zone: 1. Try a different seating position. 2. Do not use this infant car seat. NOTE: Vehicle must be parked on horizontal surface during this installation. (fig.c) ReclineIndicatorGreenStripedZone(fig.b) 32 897897 33 Check for secure installation. Pull front to back and left to right to check for secure installation (fig. d). Vehicle lap belt MUST stay tight. If vehicle lap belt does not stay tight, see “Installation with Lap/Shoulder Belts” below. Recheck car seat recline. Verify line is in green striped zone of recline indicator. Carry handle should be kept in the carry position, (see “Carry Handle Operation” section). (fig. d) Installation with Lap And Shoulder Belts: • When using vehicle lap and shoulder belts, shoulder belt may be used for additional support. Place shoulder belt around back of Combi Connection™ (fig. e) and through the vehicle shoulder belt guide on back of car seat shell (fig. f).If shoulder belt is too short to go around back of Combi Connection™, position shoulder belt against vehicle seat back (fig. g). Do not route shoulder belt through lap belt guides on either side of car seat. (fig. e) (fig. f) • Lap/shoulder belt with free sliding latch plate: -Pull out on latch plate (fig. h). If belt slides freely through latch plate, a locking clip must be used as described in “Locking Clip” section. -Some combination lap/shoulder belts with free sliding latch plates may be converted into an “automatic locking mode” that will allow use without a locking clip. See vehicle owner’s manual and label on vehicle belts for instructions. (fig. g) (fig. h) 34 ShoulderBeltGuide Unhook shoulder belt from behind car seat and unbuckle vehicle seat belt. Remove lap belt from vehicle lap belt guides. Remove car seat from vehicle. 35 Removal Of Infant Car Seat From Vehicle: 123 Section10StrollerorTravelSystemUse This infant car seat can only be used with certain Combi stroller models to transport your infant. Check Combi stroller information or the Combi USA, Inc. website at for an updated list of stroller models that will work with your Combi Connection Infant Car Seat. See stroller instructions for securing car seat an...
Эта инструкция также подходит к моделям:Автокресла - INFANT CAR SEAT 8040 (887.56 kb)