Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Philips, модель CSP6920/00

Производитель: Philips
Размер: 431.55 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Option 1: Mount on door (front or rear) B You can mount the speakers on the front/rear door of your car. a Note • Make sure that nothing obstructs around the mounting location of the door. • A hole for mounting may already be cut out of the inner panel of the door (front or rear). In this case, you need to modify the board only. • Ensure that the speaker terminals, frame or magnet do not inter fere with any inner par ts, such as the window mechanism in the door (when you open or close the window), etc. Also ensure that the speaker grille does not touch any inner fittings, such as the window crank s, door handles, arm rests etc. 1 Turn off the car ignition key. • If the power is on, the click noise generated by the connection may damage the speakers. 2 Cut out the mounting template from the packing box. 3 Paste the template on the location selected for mounting the speaker. 4 Mark the cut-off hole and the 4 bolt holes. b 5 Cut out the marked area and drill the bolt holes. c 6 Remove the grille net. d 7 Strip the speaker wires and connect them to the amplifier. e • Black wire: connect to “-“ (negative) terminal • Black (white lined): connect to “+“ (positive) terminal Note • Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may degrade sound quality. • Two 4-ohm speaker s, wired in stereo, present a 8 ohm load to each channel of the amplifier. Most two channel amplifier s work well in this configuration. However, if two 4-ohm speakers, wired in parallel to a bridged two -channel amplifier, present a 2-ohm mono load to the amplifier. Most 2-channel amplifiers do not suppor t 2-ohm mono operation! Amplifier damage may result! 8 Mount on the speaker as shown below. f 9 Press and inser t the edges of the grille net. g Tip • The speaker grille can be mounted without the grille net, if you like. Option 2: Mount on rear tray C You can also mount the speakers into the surface of the rear tray. Follow the steps in section “Option 1: Mount in door” to mount the speakers into the rear tray: 4. Product information Note • Product information is subject to change without prior notice. Model CSP620 CSP6920 CSP7020 Speaker type 16.5cm, 3-way triaxial speaker 16x24cm, 5-way coaxial speaker 18x26cm, 5-way coaxial speaker RMS power (Watts) 80W 80W 85W Peak music power (Watts) 400W 480W 550W Sensitivity (dB/W/m) 90dB 91dB 91dB Frequency response (Hz) 35-32kHz 27-33kHz 26-33kHz Impedance (ohms) 4 ohms 4 ohms 4 ohms Magnet mass (Oz) 8.6Oz 22Oz 22Oz Mounting depth (mm) 59mm 88.1 mm 85 mm 5.Troubleshooting To keep the warranty valid, never tr y to repair the system yourself. If you encounter problems when using this apparatus, go to the Philips web site (When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. © 2010 Koninklijke Philips Electronics N.V. All rights reserved. CSP620_6920_7020_00_UM_V1.0 ...

Эта инструкция также подходит к моделям:
Автоакустика - CSP620/00 (431.54 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории