Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
(Refer to the trim ring information at the end of this section.) © 2003 Directed Electronics, Inc Tweeter Surface Mounting 1. Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. 2. Place the surface mount housing against the panel and mark the two holes at the rear of the housing. 3. Drill the smaller center hole using a 1/8" drill bit. This is the mounting screw hole. 4. Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet. FIGURE 4—TWEETER SURFACE MOUNTING 5. After removing the surface mount tweeter assembly trim ring, route the tweeter wires through the larger hole in the housing and connect to the speaker wires from the crossover. (See Figure 4.) 6. Insert the excess speaker wire into the hole and position the housing so the housing will not pinch the wires after final mounting. 7. Attach the housing using the supplied screws of the correct length for a solid mount. 8. Insert the tweeter into the housing and attach the trim ring. © 2003 Directed Electronics, Inc Removing Trim Rings Hold the tweeter housing while gently turning the trim ring in a clockwise direction until it releases. The trim ring can then be easily lifted away from the tweeter housing. Installing Trim Rings • F FFl llu uus ssh hh M MMo oou uun nnt tt A AAs sss sse eem mmb bbl lly yy - With the arrow in the tweeter housing facing up, place the trim ring into the CROSSOVER INSTALLATION housing with the Viper logo at the bottom and turn in a counter clockwise direction until the trim ring clicks into place. • S SSu uur rrf ffa aac cce ee M MMo oou uun nnt tt A AAs sss sse eem mmb bbl lly yy - Insert the trim ring into the housing and turn in a counter clockwise direction until the trim ring clicks into place. Review the Installation Precautions section of this guide before proceeding. Crossover Adjustment and Wiring Connections This Directed crossover has the ability to work in car audio systems from basic FIGURE 5—SINGLE AMPLIFIER single amplifier systems to the most sophisticated multiple amplifier systems with signal processors and amplifier channels dedicated to each speaker. . © 2003 Directed Electronics, Inc SPECIFICATIONS Directed model s550 s650 Frequency response 45Hz-21kHz 40Hz-21kHz Power handling RMS 50 60 Power handling peak 100 120 Impedance 3.764 3.435 Magnet weight 52.82 g 5282 g Vas 3.25L 9.28L Fs 88.63 Hz 65.44 Hz Qts 0.42 0.33 Efficiency (1W/1M) 89.209 89.718 Mounting Depth 2.12 2.45 Mounting hole diameter 4.75 5.5 C CC o oo m mm m mm o oo n nn D DD r rr i ii v vv e ee r rr S SS p pp e ee c cc i ii f ff i ii c cc a aa t tt i ii o oo n nn s ss : :: Magnet type Neodymium Neodymium Magnet diameter 1” 1” Voice coil former Kapton Kapton Voice coil diameter 1” 1” Voice coil layers 4 4 T TT w ww e ee e ee t tt e ee r rr : :: Fs 1.2 kHz Efficiency (1W/1M) 90 dB Crossover 12 dB per octave withtweeter protection © 2003 Directed Electronics, Inc The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security, car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electronic Directed Electronics, Inc. technology, Directed is ISO 9001 registered. Vista, California 92083 Directed® is committed to delivering world-class quality products and services that excite and delight our customers. Directed is a proud member of Quality Directed products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services © 2003 Directed Electronics, Inc. -All rights reserved -G33550/33650 03/03 ...
Эта инструкция также подходит к моделям:Автоакустика - s650 (239.54 kb)
Автоакустика - s550 (239.54 kb)
Автоакустика - s550 (239.54 kb)