Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
The lighting features of all illuminite products require a 12 volt DC power source to operate. The speaker has two distinct sets of input terminals. The first is labeled audio input terminals and the second is labeled illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. The polarity (+ and -) indicators for each set of inputs also appear on these labels. 1. Do not connect amplifier or any audio source to illuminite lighting inputs. Inputs are designed for switched 12 volt DC power source only. 2. See fig. 1a, (illustrated wiring diagram) be sure to maintain polarity. Be sure to connect to a switched 12 volt DC source. Correct connection would be the positive (+) 12 volt wire to the Positive (+) illuminite Lighting input terminal and connect the Negative (-) illuminite lighting input terminal to a good chassis ground. Fig 1a Audio Input Terminals Illuminite Lighting Input Terminals Lighting Hook-Up From Rear Audio 12 Volt Source GroundSource Notice: The illuminite series LED illumination elements are not removable. There are no serviceable parts inside or attached to the speaker assembly. The illuminite series products are sensitive electronic devices. Removal or tampering with any part or portion of the speaker and/or its assemblies will damage the product and void the limited warranty. TS SERIES INSTALLATION Mounting 1. Determine where the speakers will be mounted. Make sure the area is large enough for the speaker to mount evenly. Also ensure the mounting location is deep enough for the speaker to fit. 2. Refer to the specification chart to determine the proper diameter hole to cut for your speaker model. 3. If supplied, use the plastic mounting ring as a template to mark the locations for the mounting screws. Drill the holes with a 3/32" bit. 4. Be sure to observe proper polarity when connecting the wires. The speaker's positive terminal is indicated with a "+" symbol. 5. Fit the speaker to the hole cut-out. Mount the speaker using the supplied screws. If the speaker grill is to be used, insert 4 screws into the grill holes and then mount the speaker. Standard Rear Deck Installation Mounting hole Cut-out Grille Speaker Standard Door Installation Grille Speaker Mounting hole Cut-out TS SERIES INSTALLATION Mounting The diagram featured above is to be used in conjunction with the specifications matrix guide below: Fractional Inches TS69 10 7/16” x 7 11/16” x 3/4” 3 11/16” 3 7/8" 9/16” 11/16” 5 7/8” x 9 1/4” 89 58Hz - 20kHz 50 150 4 TS65 7” x 13/16” 2 7/8” 3 1/2" 7/8” 9/16” 5 7/16” 88 65Hz - 20kHz 50 140 4 TS55 6 3/16” x 9/16” 2 5/16” 2 7/16" 5/8” 1/2” 4 5/8” 89 90Hz - 20kHz 50 135 4 TS45 5 1/4" x 5/16" 1 3/4” 1 15/16" 7/16” 5/16” 3 11/16” 89 100Hz - 20kHz 40 120 4 TS5768 9 5/16” x 6 11/16” x 1/2” 2 3/4” 2 15/16" 7/16” 1/4” 5 3/16” x 7 1/2” 89 63Hz - 20kHz 50 150 4 TS SERIES WARRANTY Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rig...
Эта инструкция также подходит к моделям:Автоакустика - ILLUMINITE TS55 (379.88 kb)
Автоакустика - ILLUMINITE TS69 (379.88 kb)
Автоакустика - ILLUMINITE TS65 (379.88 kb)
Автоакустика - ILLUMINITE TS65 (379.88 kb)