Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
4. Frequency Response 50–20,000Hz 35–20,000Hz Mounting Hole Cutout 5" 6" x 8 11.16" (ellipse) Mounting Depth 2 1.2" 64mm 3" 76mm Mounting Depth w/Spacer 2" 51mm 3 1.2" 89mm Table of Contents Specifications Table of Contents Notice Tools Required Before You Begin Planning the Installation Speaker Wiring Routing the Wires Installing Speakers In Factory Cutouts Installation Options Installing Speakers In Nonstandard Locations-RM6 Installing Speakers In Nonstandard Locations-RM9 Warranty 16 Notice Installation of automotive stereo systems requires experience with a variety of mechanical and electrical procedures. This manual explains the installation flexibility of the Boston Rally Series speaker systems, not the exact installation methods to be used in any given case. If you do not have the experience that these procedures require, we strongly suggest you consult your Boston Acoustics dealer about professional installation. Tools Required These are the tools required to complete the basic installation of the Boston Rally Series speakers. Additional tools are necessary for more custom work. 1. Electric drill with 1.8" (3mm) and 1.4" (6mm) bits 2. Phillips screwdriver 3. Saber saw, hole saw or nibbler 4. Utility knife 5. Silicon sealant or weather stripping (optional) 6. Pliers or 7mm wrench (RM9 only) Before You Begin Familiarize yourself with the location of fuel lines, hydraulic brake lines and electrical wiring. Use extreme caution when cutting or drilling around these parts. Shut off all stereo and other electrical devices before you start. Protect the speakers by keeping them in their plastic bags until final installation. Speakers attract metal chips and filings. Always rest the speakers with their cones and tweeters facing up. Never use force when installing any speaker. Check clearances on both sides of a mounting surface before drilling any holes or installing any screws. Some screws require over an inch of clearance behind the mounting surface. Use a utility knife to cut fabric away from hole locations before you drill or cut. Fabric is easily snagged by drill bits and hole saws. Always wear protective eyewear when cutting and drilling holes or when using power tools. Planning the Installation Read all instructions carefully before you attempt any installation procedures. Make sure all operations are clear to you. Make sure you have adequate time and shelter to complete the installation. Many installations require multiple days to complete. Examine the Boston Rally Series speakers and hardware so that you are familiar with them before you start the installation. 1. Decide on speaker placement. 2. Run the speaker wires. 3. Install the speakers and complete the wiring. Speaker Wiring For your convenience, two sets of two-conductor wire are provided to use between the speakers and the amplifier or head-unit. Other wire may be substituted if desired as long as it is at least 18 gauge. Sometimes the stock speaker wires in the vehicle may be used. Two-conductor speaker wire connects the positive and negative terminals of each speaker to the corresponding positive and negative terminals on the amp or head-unit. One side of the wire will be marked in some way. Use the marked conductor to connect the positive terminals and the plain conductor to connect the negative terminals. stripe on one side ridge on one side different color wires thread on one side Routing the Wires Include a large safety margin when estimating the length of each wire. For Doors: Run the wires through factory harnesses or existing holes, if possible. If drilling new holes, file the edges and install rubber grommets and PVC tubing to protect the wires against abrasion. For Rear Deck: Run wires along the door sills just inside the car, lifting and replacing carpet as required. You may have to remove the rear seat to pass wires back to the rear. Installing Speakers In Factory Cutouts 1. Make sure the mounting surface provides a complete air seal between the front and the back of the speaker. If the surface is uneven, or if air can leak directly from the back of the speaker to the front, seal the air leaks with silicon sealant or weather stripping. Make sure that the sealing material does not touch any moving part of the speaker. 2. Attach the wires to the speaker. 3. Attach the assembly to the factory cutout using four of the supplied #8 sheet metal screws or other hardware. Tighten the screws just enough to seal the woofer against the mounting surface. Do not overtighten the screws. RM6 Installation Option Most factory speaker locations for 6-inch speakers provide either three or four screw holes for mounting the speaker. The RM6 includes both sets of holes. Rotate the speaker until the correct holes line up. 4-hole pattern 3-hole pattern RM9 Installation Option The RM9 can also be installed from underneath the rear deck to reduce the installed height of the tweeter module. A spacer is supplied to protect the rubber surround and ensure a ti...
Эта инструкция также подходит к моделям:Автоакустика - RALLY RM9 (624.61 kb)