Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
DO NOT CONNECT AMP OR ANY AUDIO SOURCE TO ILLUMINATION INPUTS AS DAMAGE TO LIGHTS WILL OCCUR. 10. Illumination connection: The positive (+) output from your 12V system connects to the positive (+) input, and the negative (ground) connects to the negative (-) input on the input cup located on the rear of the subwoofer enclosure. Improper 12V polarity will not cause damage to the lights, but they will not illuminate. XOBP12D GUIDELINES Enclosure Guidelines To achieve the best possible sound from this subwoofer enclosure, Dual recommends aquiring the services of a professional car audio installation center. If you feel confident in your ability to install this product without the assistance of a professional, please read this section thoroughly. We have provided a number of placement recommendations and installation tips to assist you. Keep in mind these are provided as a guideline and you may find that other placements specific to your vehicle may provide better results. Make sure all moving parts and factory electrical wires are out of the way and will not interfere after installation. Ensure the wire is of sufficient length to avoid pulling or stretching. This is even more important if the wires will be run under or through the factory interior. Use electrical tape and wire ties to ensure all wires are properly secured. Avoid installing speakers or electronics where they can be subject to moisture. Ensure the speaker wires are connected using correct polarity. The positive polarity is marked by a (+) sign. Incorrectly connected subwoofers will result in limited bass output. Ensure the Illuminite wires (12V) are connected using correct polarity. Do not connect an amplifier or any audio output source to the Illuminite inputs as doing so will cause permanent damage to the lighting elements. Speaker wire should be isolated from the vehicle's electrical system to avoid noise being picked up by the amplifiers. We recommend using 14 gauge or larger sized speaker wire to ensure your subwoofer receives the full power output of your amplifier. Remember to listen responsibly and respect your ears. Being exposed to sounds over 125dB for even short periods of time can create permanent hearing loss! XOBP12D INSTALLATION IlluminiteTM Lighting Hook-Up Recommendations Dual's patent-pending Illuminite bulb system and contr ol circuitry provide for extraordinary blue illumination, allowing for creative color-coordinating installations. The interior of your vehicle will never sound or look ordinary again! Let your imagination take you there. The lighting features of all Illuminite products require a 12V power source to operate. The speaker has two distinct sets of input terminals. The first is labeled audio input and the second is labeled Illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. The polarity (+ and -) indicators for each set of inputs also appear on these labels. 1. Do not connect your amplifier or any audio source to the Illuminite inputs. These inputs are designed for switched 12V DC power only. Do not connect directly to your battery permanently, as it will cause your battery to discharge. Please use a switched 12V source. 2. See Fig. 1a, (illustrated wiring diagram) to be sure to maintain polarity. Be sure to connect to a switched 12 volt source. Proper connection would be the positive (+) 12V wire to the positive (+) Illuminite input terminal and the negative (-) Illuminite input terminal to a solid chassis ground. DO NOT CONNECT AMP OR ANY AUDIO SOURCE TO ILLUMINATION INPUTS. DAMAGE TO LIGHTS WILL OCCUR AND WARRANTY WILL BE VOID! Fig 1a Lighting Hook-Up From Rear From Amplifier Notice: The XOBP12D Illuminite lights are not removable. There are no serviceable parts inside or attached to the speaker assembly. The XOBP12D is considered to be a sensitive electronic device. Removal or tampering with any part or portion of the speaker and/or its assemblies will damage the product and void the warranty. XOBP12D GENERAL FEATURES General Features Input Terminal Cup -The input terminal cups provide a quick and easy connection from your amplifier to the enclosure, and 12 volt inputs to power the Illuminite feature Computer tuned acoustic chamber - Dual's enclosur es utilize a specialized tuned-port computer aided design to increase the output efficiency Low Q optimized subwoofers will create loud yet very accurate bass Curved Plexiglas Viewing Window Super durable carpeted enclosure Nailed and glued construction with added bracing is used to eliminate enclosure movement caused by high sound pressure levels In-line LED protection circuitry On-Off Illuminite toggle switch Removable Illuminite Logo made of static poly material can be placed on any window or glass surface XOBP12D WARRANTWARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state..... Dual Electronics Corp. war...
Эта инструкция также подходит к моделям:Автоакустика - XOBP12D (427.04 kb)