Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
When docked, your iPhone/iPod will charge until fully charged while the iP51 is connected to an AC outlet. This unit will not overcharge theiPhone/iPod. If you dock an iPhone/iPod while the iPhone/iPod is in play mode, the iP51 will automatically switch to iPhone/iPod mode and play your music. b) If iPhone/iPod is not playing when docked, press the Button to play the iPhone/iPod, and again to pause. c) Press the or buttons to adjust iP51 volume up or down. Use the Sub Level Knob on the subwoofer to adjust bass volume level. d) Press the EQ button to cycle through the EQ (tone) settings: treble, bass, 3D sound effect, and balance. Press the ..or .. Button to adjust the EQ settings. e) Press the Button to turn the iP51 and iPhone/iPod off. Using the AM/FM Radio a) Make sure the AM antenna is properly attached and both AMand FM antennas are extended/located for best reception. b) Press the Radio/Aux button. By default, the FM band is selected, but the unit will revert to the last band in use (AM or FM). Press the Radio/Aux button to toggle between FM and AM bands. c) To tune a station, press the ..or ..Button until the desired frequencyappears (hold either button for faster selection; the unit will scan to thenext station with clear reception). d) To save a station as a preset, tune in the desired station then hold the desired preset button for about two seconds until you hear a confirmationbeep. You can save up to 12 presets (6 AM and 6 FM). To change a preset, follow the same steps for saving a preset. e) To listen to a preset station in radio mode, press the Radio/Aux button to select the desired radio band (AM or FM), then pressthe desired preset button. The unit will tune to the preset station assigned in the selected band. Using the Line-in Jack a) Use an audio patch cord (available at to play nondocking iPhone/iPod models or other audio devicesthrough the iP51 Line-in Jack (one end in the device’s line out or headphones jack, the other in the iP51 line in jack). Press the Radio/Aux Button until LINE IN appears in the display. You can now play your device. Using the Dimmer a) During normal operation, press the Dimmer Button to cycle through brightness display settings to the one you prefer. Using the Composite Jack To output iPhone/iPod video signal from the iP51 to your TV, connect it to your TV system with a composite video cable (not included). Plug one end into your TV video/audio-in jack(s) and the other end to the composite video out jack located on the back of the iP51. Turn on your TV and select the input for the AV-in jack signal. Playing video from your iPhone or iPod will output the video signal to yourr TV. 8 Using the Alarms Setting the Alarms 1. Press and hold the or Button until the alarm time display flashes. Press the or Button to set the alarm time (hold for a few seconds to advance or reverse rapidly). Remember to set the correct AM or PM wake time. 2. Press the or Button again. The currently selected alarm frequency will flash. Press the or Button to select to wake to the alarm for 7 days (everyday), 5 days (week days) or 2 days (weekends). Make sure the calendar is properly set for accurate wake frequency. 3. Press the or Button again. The current wake source display will flash. Press the or Button to select iPhone/iPod, Playlist, Radio or Buzzer to wake to. 4. Press the or Button again or wait for 10 seconds. The alarm is now armed, indicated by the numbered alarm clock icon. NOTE: To wake to playlist mode, first create a playlist named ‘ihome’ on your iPhone/iPod. Arming and Disarming Alarms (Turn Alarm Function On and Off) 1. Alarms are automatically armed when set, indicated by the alarm icon. Press the or Button to arm or disarm the alarms. Resetting the Alarm to Come on the Next Day 1. When the alarm is sounding, press the Button to stop the alarm and reset it to come on the following day at the same time. Snooze 1. Press and hold Snooze Button to adjust snooze timer from 1 to 30 minutes. 2. Press the Snooze Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes later. Snooze can be pressed several times during the 1 hour alarm cycle. Sure Alarm The iP51 has a sure alarm feature. If backup batteries are installed, the buzzer alarm will sound in the event of a power failure. If your iPhone/iPod has no sound for 20 seconds or is not present, the iP51 will switch to buzzer alarm automatically. Replacing iP51 Backup Batteries Install/Replace Backup Battery The iP51 uses a backup battery system to provide continuous clock settings in the event of a power failure. If the Battery Low Icon located on the right of the display is flashing, it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise all settings may be lost during battery replacement. • Open the battery compartment cover located on the bottom of the main receiver unit. Insert 2 “AA” batteries as indicated. We recommend the use of al...