Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
If the NV-WIPS does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/ TV technician for help. CE Statement NuVo Technologies, LLC declares that the NV-WIPS conforms to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC: · EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment. · EN 609 50 Safety · EN 300-328 Technical requirements for Radio equipment. Caution:This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow. Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW equivalent isotropic radiated power (EIRP) are considered as not compliant with the above mentioned directive and are not allowed for use within the European community and countries that have adopted the European R&TTE directive 1999/5/EC. For more details on legal combinations of power levels and antennas, contact NuVo Technologies, LLC. IC Statement This Class B digital apparatus complies with Canadian ICES-003 and RSS210 rules. Cet appareil numerique de la classe B est conforme a la norme NMB-003 et CNR210 du Canada. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device has been designed to operate with the antennas listed below, and having a maximum gain of 2.0 dBi @ 2.4GHz. Antennas not included in this list or having a gain greater than 2.0 dBi @ 2.4GHz are strictly prohibited for use with this device.The required antenna impedance is 50 Ohms. Package Contents SKU Description Quantity NV-WIPD Wireless NuVoDock for iPod 1 NV-WIPR Wireless Receiver for NuVoDock 1 NV-PSW12A Universal Power Supply including USA, UK, EU, AU adaptors 1 NV-NC1 CAT5 Cable, 10 foot, Black 1 NV-CMR6B 3.5mm Mini to RCA Stereo Audio Cable, 6 foot, Black 1 Installing the Wireless NuVoDock The Wireless NuVoDock is designed to communicate with the Grand Concerto and Essentia E6G Systems. Installation and setup require a few simple steps. Step 1: Place the NuVoDock and NV-PSW12A power supply in a zone location. Likewise, place the NV-WIPD wireless receiver with the Grand Concerto EZ Port or Esssentia E6G AllPort connection hub. Step 2: Set the Source Input Switch to the appropriate source input number 1-6 on the bottom of the NV-WIPD and the back of the NuVoDock.This must coincide with the source input on the back of the NuVo amplifier.This step must be done prior to connecting the power supply. Step 3: Complete the connections at the NV-WIPD wireless receiver. Plug the CAT5 Network connection into one of the “Device” inputs on the EZ Port or AllPort, and the NV-CMR6B stereo mini to RCA audio cable from the audio output on the NV-WIPD wireless receiver to one of the six source inputs on the back of the NuVo amplifier. Step 4: Make sure the NuVoDock is plugged into an AC power outlet. Step 5: Once the Wireless NuVoDock is installed and the Grand Concerto/ Essentia System is installed, you will be able to place an iPod in the NuVoDock (see the Supported iPod Models page for compatible iPod versions) for communication with the system Control Pads. The iPod display will be replaced with the NuVo logo when in NuVoNet communication, and return to normal iPod display when the iPod is removed from the NuVoDock. * Note:When using a iPod Touch on the NuVoDock it will display “Accessory Attached” instead of displaying the NuVo logo. Each NuVoDock represents an audio source input for the NuVo system and up to two wireless NuVoDocks can be used in a single NuVo system. If you are using the I8G-E6G Configurator software for setup, select the NuVo NV-WIPS IR library within the Source Tab for each Wireless NuVoDock used. Supported iPod Models Model Universal Dock Adaptor (Apple Part #) Min. iPod Firmware Version MC395ZM/A 1.0.1 MB569G/A 2.2.1 2.0.3 MB568G/A 1.0.4 MA126G/A 2.0.3 MB127G/A 1.1.5 MB126G/A 1.1.3 MA125G/A 1.1.2 MA593G/A 1.1.3 MA126G/A 1.3 MA125G/A 1.3 MA124G/A 1.3.1 Universal Dock Min. iPod Model Adaptor Firmware (Apple Part #) Version MA121G/A 1.4.1 MA119G/A 3.1.1 MA120G/A 3.1.1 MA123G/B 1.2.1 MA122G/B 1.2.1 Specifications RF Fr...