Оценок - 0, средний балл: 0
(
)
)
|
Фото и характеристики Yamaha HS5 |
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always turn the power off when the device is not in use. PA_en_1 2/2 HS8/HS7/HS5/HS8S Owner’s Manual 5 NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. • Handling and Maintenance • Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components. • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel. • When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. • Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out. • During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the device. If water is left, the wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately with a soft cloth. • Interference From Cell Phones Using a cell phone near the speaker system can induce noise. If this occurs, move the cell phone further away from the speaker system. • Air blowing out of the bass reflex ports is normal, and often occurs when the speaker is handling program material with heavy bass content. • Always turn the power off when the device is not in use. • Avoid touching or allowing objects to come in contact with the speaker diaphragms. • These speakers should be used vertically, not laid on their side. • Connectors • XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-). Information • About this manual • The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. • Steinberg and Cubase are registered trademarks of Steinberg Media Technologies GmbH. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. 6 HS8/HS7/HS5/HS8S Owner’s Manual Rear Panel The HS8/HS7/HS5/HS8S switches and connectors are located on the rear panel, as described below. HS8/HS7/HS5 1 2 3 4 Speaker Input and Response Control 1 LEVEL control Adjusts the output level of the speaker. When set to the 12-o’clock position the speaker is optimized for a nominal input level of +4 dB. 2 INPUT 1/2 connector These connectors receive the input signal to the speaker. Two input connectors are provided: one balanced XLR connector, and one balanced (TRS) phone jack. NOTE The XLR and phone jack input connectors can not be used simultaneously. Use only one input connector at a time. NOTE Refer to “Connection and Cable Types” on page 14 for more connector details. 3 ROOM CONTROL switch Adjusts the speaker’s low-frequency response. This switch can be used to compensate for exaggerated low-frequency response that can be caused by reflections in some listening environments. Setting the switch to the [0] position produces a flat frequency response. The [-2 dB] setting attenuates the range below 500 Hz by 2 dB, and the [-4 dB] setting attenuates the range below 500 Hz by -4 dB. 4 HIGH TRIM switch Adjusts the speaker’s high-frequency response. Setting the switch to the [0] position produces a flat frequency response. The [+2 dB] setting boosts the range above 2 kHz by 2 dB, while the [-2 dB] setting attenuates the range above 2 kHz by -2 dB. 5 6 5 Power switch Turns power to the speaker ON or OFF. Rock the switch to the right [ ] to turn the power ON, or to the left [ ] to turn the power OFF. The Yamaha logo on the front panel will light when the power is ON. NOTE Turning the power switch ON and OFF in rapid succession can cause the device’s electronics to malfunction. Please wait for 3 seconds or more after turning the power OFF before turning it ON again. 6 AC IN connector Connect the supplied power cable here. First connect the power cord to the speaker, then insert the power cord plug into the AC outlet. English HS8/HS7/HS5/HS8S Owner’s Manual 7 ) 3 6 8 9 1 2457 Subwoofer Connections 1 INPUT L/R connector These connectors receive the input signal to the subwoofer. Balanced XLR and balanced phone jack connectors are provided for both the L and R inputs. The L and R inputs can be used simultaneously. Signals supplied to both the L a...
Эта инструкция также подходит к моделям:Акустика - HS7 (2.4 mb)
Акустика - HS8 (2.4 mb)
Акустика - HS8S (2.4 mb)