You can also operate the remote at a horizontal angle of up to 30° from the remote control sensor. 9 10 power on and volume control tUrning tHe POWer On/Off MUTE BASS FUNCTION VOL MUTE BASS FUNCTION VOL AUX IN DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH DOCK ONLY FOR SERVICE ONLY FOR SERVICE DOCK DOCK DOCK DOCK or 1. To turn on this unit, press any button on the unit's top panel when the unit is in Standby mode. or, Press POWer on the remote control. 2. To turn off this unit, press the +# button on the unit's top panel for more than 3 seconds. or, Press POWer on the remote control again. . The standby LED is on when AC Plug is connected to the wall outlet and the Power of the unit is off. The standby LED is off when the power of the unit is on. . The power of the unit automatically turns off if there is no input for 20 minutes. aDJUsting tHe VOLUMe Use +, - buttons to adjust the volume. As you adjust the volume, the Input mode LED blinks. The LED remains on in case you increase the volume when it has already been set to maximum, or decrease the volume when it has already been set to minimum. MUTE BASS FUNCTION VOL MUTE BASS FUNCTION VOL AUX IN DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH DOCK ONLY FOR SERVICE ONLY FOR SERVICE DOCK DOCK DOCK DOCK or Press the +/– button on the right side of the top panel. or, Press vOl +/– on the remote control. . The volume level increases or decreases when you press VOL +/–. . You can also use the volume controls of devices connected using the Dual Dock or Bluetooth to control the volume. However, your ability to control the volume using the volume controls of devices connected using Bluetooth may be limited. connections Using tHe sPacer cOVer EnG Attach the space cover if you want to dock a Samsung Galaxy or Apple device having no protective case onto the Dual Dock. -Use it for stable installation of your device considering the shape of the device. The Dual Dock also comes with a protective cover for the 30-pin Apple device connector. Use the protective cover for the 30-pin connector when you attach the 5-pin Samsung Galaxy device. See the illustrations below for additional instructions. . connEctions When docking a device, use appropriate support considering the docking device’s protective case or the device’s shape for further stability. Protective Cover Used for docking devices having no protective case on it. Spacer Cover Protective Cover Spacer Cover . It is impossible to attach a device to the Dual Dock that has a case thicker than 1.5 mm or an unusual rounded bottom. 11 12 cOnnecting a DeVice tO tHe DUaL DOcK How to connect a device to the Dual Dock. 1. The DUAl DOcK is located on the back of the product. To open, push it in gently. 2. If you have a Samsung Galaxy device, connect the device to the 5 pin (smaller) connector to connect to the Dual Dock. If you have a Apple device, connect the device to the 30 pin (larger) connector on the Dual Dock. 3. Lift the device support up as shown to prevent the device from sliding or falling off the Dual Dock. . Turn on your Samsung Galaxy device before you attach it to the Dual Dock. . This unit doesn't support the simultaneous docking of Samsung Galaxy and Apple devices. . Connect your Samsung Galaxy or Apple device to the Dual Dock before starting Docking mode. (See page 16) AUX IN ONLY FOR SERVICE DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH DC 12V 2A AUX IN ONLY FOR SERVICE PUSH PUSH DC 12V 2A AUX IN ONLY FOR SERVICE DC 12V 2A AUX IN ONLY FOR SERVICE PUSH PUSH DC 12V 2A AUX IN ONLY FOR SERVICE 13 EnG . connEctions AUX IN DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH ONLY FOR SERVICE ONLY FOR SERVICE AUX IN DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH ONLY FOR SERVICE ONLY FOR SERVICE AUX IN DC 12V 2A PUSH AUX IN ONLY FOR SERVICE DC 12V 2A PUSH ONLY FOR SERVICE ONLY FOR SERVICE AUX IN Earphones jack audio cable (not supplied) external Device cOnnecting an aUDiO DeVice Using aUX in This section explains how to connect the unit to an audio device. This unit requires one analog audio jack for connecting to an audio device. AUX in Connect AUX IN (Audio) on the back of the unit to the earphone jack of the external device or audio device. if connected to an external device via AUX input while your Samsung galaxy device is docked or connected to a bluetooth device at the same time, the input source switches between the AUX and Samsung galaxy or bluetooth device by tapping the PAUSe button on the Samsung galaxy / bluetooth device. tap it again to switch to the other input source. . Use the Function key on the remote control to switch between connected devices, if there are multiple devices connected to the Docking station. . Before moving or installing this product, be sure to turn off the power and disconnect the power cord. BLUetOOtH You can connect the Wireless Audio with Dock to Bluetooth devic...
