Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Always follow the instructions in this chapter in sequence. Connect speakers For optimal sound, use the supplied speakers only. Note ••The supplied DIN cable is only intended for use with this product. Never try to connect any other devices through this cable. Connect the supplied DIN cable to the CABLE IN sockets on both speakers: • active speaker (with buttons): right channel • passive speaker: left channel Connect power Caution ••Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the bottom of the unit. ••Before connecting the AC adaptor, ensure you have completed all other connections. ••Risk of electric shock! When you unplug the AC adaptor, always pull the plug from the socket. Never pull the cord. Connect the AC power adaptor to • the DC-IN socket on the back of the active speaker. • the wall power outlet. UKEUR EN Turn on In standby mode, there are two ways to turn on the unit. • Audio signal detected from the 30-pin connector or from the AUX-IN port . »»The ring tone is also recognized as audio signal. • Press the SYNC button on the top of the active unit. »»Turn on the unit by pressing SYNC button will bring the unit into sync mode. Note ••There is no power key on the unit. It turned on automatically when it detects an audio input. Switch to standby mode The unit switches to standby mode in the following situations. • In DOCK mode: no audio signal from docked iPod/iPhone over 15 minutes. • In MP3 link mode: no audio device connected over 15 minutes. • In SYNC mode: press SYNC button for over 5 seconds. »»The power indicator turns off. 4 Play Play from iPod/iPhone You can enjoy audio from iPod/iPhone through this unit. Compatible iPod/iPhone The unit supports the following iPod/iPhone models. Made for. • iPod touch (1st, 2nd, 3rd, and 4th generation) • iPod classic • iPod nano (2nd, 3rd, 4th, 5th, and 6th generation) • iPhone 4S • iPhone 4 • iPhone 3GS • iPhone 3G • iPhone Load the iPod/iPhone • Insert your iPod/iPhone into the dock. Remove the iPod/iPhone • Pull the iPod/iPhone out of the dock. EN Charge the iPod/iPhone When the unit is connected to power, the docked iPod/iPhone begins to charge automatically. Listen to the iPod/iPhone Note ••Make sure that your iPod/iPhone has been loaded securely. • Start music play in your iPod/iPhone. »»You can hear music from the speakers. Play from an external device You can enjoy music from an external device through this unit. Note ••If the unit can detect audio signal from 30-pin connector and AUX-IN port at the same time, it should work under DOCK source. Play from an external device with MP3 link cable 1 Connect MP3 link cable to: • the AUX-IN socket on the back of the active speaker. • the headphone socket on an external device. 2 Start to play on the device . 5 Other features Synchronize the iPod/iPhone with a PC 1 Insert the iPod/iPhone into the dock. 2 Connect the active speaker to your PC through the supplied USB cable. 3 Press on the active speaker. »» The LED indicator flashes. 4 Start iTunes to snychronize your docked iPod/iPhone with the PC. Note ••Make sure that you have not disabled automatic synchronization in iTunes. Otherwise , start synchronization from iTunes manually. To exit synchronization mode: 1 Eject your iPod/iPhone from iTunes . 2 Press on the active speaker. »»The speakers return to audio mode . AUX-IN EN 6 Product information Note ••Product information is subject to change without prior notice. Specifications Amplifier Rated Output Power 2 x 10 W RMS Frequency Response 60-20000 Hz, ±3dB Signal to Noise Ratio > 77 dB MP3 Link 600 mV RMS 22 kohm Speakers Speaker Impedance 4 ohm Speaker Driver 2.5 inch full range + dia 60mm x 2 Woox General information AC power Model: AS360-120- AQ300 Input: 100-240 V~, 50/60 Hz 1.2 A Output: 12.0 V 3A Operation Power Consumption 10 W Standby Power consumption <0.5 W Dimensions - Main Unit (diameter x height) W148*D148*H150mm Weight - With Packing - Main Unit 3.3 kg 0.8 kg 7 Troubleshooting Warning ••Never remove the casing of this apparatus. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site (philips.com/welcome). When you contact Philips, ensure that the apparatus is nearby and the model number and serial number are available. No power ••Make sure that the AC power plug of the device is connected properly. ••Make sure that there is power at the AC outlet. No sound ••Adjust the volume. ••Check whether you have started music play. No response from the unit ••Disconnect and reconnect the AC power plug. EN 8 Notice Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user’s authority to operate the equipment. This product complies with the radio interference requirements of the European Community...