Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
To disconnect the cord, pull the cord by grasping the plug. Never pull the cord itself. • Should any liquid or solid object fall into the woofer, unplug the woofer and have the woofer checked by qualified personnel before operating it any further. • AC power cord must be changed only at the qualified service shop. When turning on or off an amplifier or other equipment Lower the volume of the amplifier to minimum. To avoid damaging the woofer • Be careful in setting the volume control of the amplifier to avoid an excessive input power. • Do not attempt to open the enclosure or remold speaker units and networks. In case color irregularity is observed on the nearby TV screen With the magnetically shielded type of the speaker system, the speakers can be installed near a TV set. However, color irregularity may still be observed on the TV screen depending on the type of your TV set. If color irregularity is observed... t Turn off the TV set once, then turn it on after 15 to 30 minutes. If color irregularity is observed again... t Place the speakers further apart from the TV set. When howling occurs Relocate the speaker or turn down the volume of the amplifier. On installation • Do not install the woofer near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. • Good ventilation is essential to prevent internal heat build-up in the woofer. Place the woofer in a location with adequate air circulation. Do not place the woofer on a soft surface. On cleaning the cabinet Clean the cabinet with a soft cloth lightly moistened with water. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. If you have any questions or problems concerning your woofer that is not covered in this manual, please consult your nearest Sony dealer. Installation Since the human ear cannot detect the direction and position where the bass sound being reproduced by a woofer (below 200 Hz) comes from, you can install the woofer wherever you like in your room. To obtain a better bass reproduction, we recommend you to install the woofer on a solid floor where the resonance is unlikely to occur. Notes • Always install the woofer vertically, keeping a few centimeters from away the wall. • Do not place an object on the woofer or sit on it. • If the woofer is installed in the center of a room, the bass could be extremely weakened. This is due to the influence of the standing wave of the room. If this happened, move the woofer away from the center of a room or eliminate the cause of the standing wave, by installing a bookshelf on the wall, etc. Hooking Up the System Overview Use the LINE IN jacks or the SPEAKER IN terminals of the woofer when you connect the amplifier. • If your amplifier has one of the following types of output jacks, connect the LINE IN jack and the amplifier's jack using the supplied audio connecting cord. — MONO OUT jack — MIX OUT jack — SUBWOOFER output jack(s) — SUPER WOOFER output jack(s) • If your amplifier does not have the above mentioned output jacks, connect the speaker terminals of the amplifier to the SPEAKER IN terminals instead. (A) Before you get started • Turn off the power of the amplifier and the woofer before making any connection. • Use the audio connecting cords that are supplied to the respective equipment. If there are not enough audio connecting cords to make the necessary connections, you need to purchase some optional audio connecting cords. • Be sure to make connections firmly to avoid noise. • Connect the AC power cord from the woofer to a wall outlet. • You cannot connect the CENTER output jack for use with Dolby Pro Logic function to the woofer. Bass sound is not output with some Dolby Pro Logic modes. Connecting to an amplifier with a single set of speaker terminals (B) If your amplifier is equipped with a single set of speaker terminals, connect the woofer to the amplifier, and then connect the front speakers to the woofer. Hookups 1 Connect the woofer to the amplifier. Connect the SPEAKER IN terminals of the woofer to the amplifier’s speaker terminals with the speaker cords. Be sure to connect both L and R channels. 2 Connect the front speakers to the woofer. Connect the speakers to the speaker terminals of the woofer. Connecting to an amplifier with double (A+B) sets of speaker terminals (C) If your amplifier has double (A+B) sets of speaker terminals, connect both the woofer and the front speakers to the amplifier. Hookups 1 Connect the front speakers to the amplifier. Connect the speakers to your amplifier’s speaker terminals (A). 2 Connect the woofer to the amplifier. Connect the SPEAKER IN terminals of the woofer to the amplifier’s speaker terminals (B) using speaker cords (supplied). When using the double (A+B) sets of speakers, make sure that you select the “A+B” position with your amplifier. Note When you are using speaker terminal (A) only (front speaker only) or when the power...